0
hello, I'm trying to remove the automatic transmission and I have a problem: I can not remove the two roll bars ranging from the support bar from the harness to change the front axle.
I removed the two transmission shafts I removed the bolts that hold the support bar of the change, I have raised before the vehicle so that the wheels do not touch the ground, and I completely loosened the bolts that record stabilizer bars, I tried to beat the bar with a hammer to support gearbox remove it from the two roll bars but does not move.
thanks
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Torsion bar on Nissan Pathfinder?
The 1st generation Nissan Pathfinder, 1987 - 1995 had a torsion bar suspension on the front end of the vehicle. There is a driver's side and passenger's side torsion bar and they are not interchangeable. 1996 - 2009 models do not use a torsion bar.
How do you remove the bar at the bottom of safari?
I'm pretty sure if you fully close Safari, the bar will dissapear.
Does ford make a tool to remove torsion bar from trunk?
t64k-44890-b
How Remove torsion bar cuda?
Jack it up take the Clip holder at the end Of it out & slide it out !!!!!
How do you replace torsion bars on a 1973 Dodge Challenger?
You remove the metal retaining clips on the back side of the frame / cross member that stop the torsion bar from sliding out. Figure out a way to clamp something to the torsion bar and smack it with a hammer driving the torsion bar towards the rear of the car. PS they do sell tools made to clamp on to the torsion bar. I would also suggest having the wheels off the ground and hanging. Also loosen the nut that adjust the ride height.
How do you replace VW Bug torsion bar system?
Your best bet would be to purchase a Haynes manual. Remember... safety first! Jist: disconnect brake lines,remove hub cap , loosen lug nuts, remove cotter pin and 36 mm, jack up car and secure on jack stands, remove wheel, remove drum brake, remove emergency brake cable, remove the clip holding brakeline and disconnect brakeline from the trailing arm. remove lower shock mount, notch the trailing arm and spring bar to ease realignment, remove driveshaft. remove 17 mm Allen nut on trailing arm and the three bolts holding trailing arm to torsion arm... remove trailing arm. Put a jack under the torsion arm and jack it up until the arm lifts slightly off of the stops. Remove the four bolts and the torsion plate, remove the outter bushing. IMPORTANT: (do at your own risk) do not get any part of your body underneath the torsion bar while in this position... you could get hurt. With a prybar, pry the torsion arm past the stops and slowly lower your jack. Once the torsion arm is under no stress, use an angle finder to find the angle (will help with reassembly). Remove the torsion arm and inner bushing. Remove the torsion bar. Assemble... in reverse probably... haven't done it yet. Hope this helps.
How do you lower the rear of a Peugeot 206?
as the rear is torsion it is not straight forward. the torsion bars have to be removed one side at a time, with the torsion bar out simply adjust hub the required amount and replace torsion bar. then do the other side. this can be hard as the bars can be difficult to remove. best left to professional should cost between £60-£100
How do you remove the suspension arm on a 1998 Toyota Hiace?
My 1993 Hiace has a Torsion Bar Suspension on the front. The tension retainer is halfway down the vehicle. Jack the vehicle up - remove the wheel, then undo the locking nut on the end of the torsion bar, ( mark with a dot of paint so that you tighten the bar to the correct vehicle height on reassembly) Once you have released the tension its a doddle to remove!!
How do you adjust the torsion bar on a Chevy 1500?
You need a torsion key.. most mechanics can twist the bar for cheap
What are torsion bars?
A torsion bar is used in an auto suspension. A torsion bar suspension, also known as a torsion spring suspension or torsion beam suspension, is a general term for any vehicle suspension that uses a torsion bar as its main weight bearing spring. One end of a long metal bar is attached firmly to the vehicle chassis; the opposite end terminates in a lever, the torsion key, mounted perpendicular to the bar, that is attached to a suspension arm, a spindle, or the axle. Vertical motion of the wheel causes the bar to twist around its axis and is resisted by the bar's torsion resistance. The effective spring rate of the bar is determined by its length, cross section, shape, material, and manufacturing process.
Torsion bar tool?
the torsion bar is actually a rod which is twisted when load is applied on opposite direction like couple
Install torsion bar 1993 Saturn sl2?
Vehicle does not have torsion bars
