0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Which way do you turn the blade bolts on a craftsman riding mower?
counterclockwise
Which way do you turn the blade bolts on a mtd riding mower?
They are standard thread. Counter-clockwise to loosen.
How do i replace the water pump om a 79 GM 350?
drain all your antifreeze out, remove your alternator, power steering and a/c belts, if you have a/c. Take the four bolts out that hold the fan blade, remove the blade, remove the pulley, and then remove the 2 bolts on both sides, on the right side of the water pump, you will see 2 bolts for the alt. bracket, you may have to remove to gain access. don't forget to undo your lower radiator hose.
How do you install blades on a 42 inch riding mower?
depending on model u need to loosen the belt there should be a bolt in the blade were it attatches on to the pulley shaft loosen the bolt take off the lock then the blade when u reinstall dont reverse blade and make sure bolts are tight or youll get vibration and put the brass bearing sleaves in disrepair you dont need to remove the deck
How do you remove your fan on your 1998 Chevy blazer to replace the water pump?
I haven't done this but my Haynes manual says that the upper fan shroud is removable to give you access to the fan blade bolts, then you have to hold the fan blade while you unscrew the bolts.
How do you change the cooling fan motor 2002 Chevy cavalier?
First unplug the fan. Second remove the bolts on the out side of the plastic fan shroud, the motor and fan blade are connected to this then remove the whole unit out of the car. Then remove the bolt that's connecting the fan blade to the motor, these bolts usually are reverse threads to you have turn the bolt to the right to remove it. i know it sounds crazy. Then the motor should come free of the plastic shroud and the blade. finally reverse the steps.
97 deville power steering r and r?
Remove the upper fan shroud, then the fan blade. Remove the P/S pulley with the proper tool, then remove bolts and reverse to re-install.
How do you remove blade tool from army Swiss knife?
remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber
How do you change blade on a cub cadet 1515 riding lawn mower?
Use an impact air wrench and a socket with some wd-40.You may need to remove the deck if so there are two pins/bolts in the front and to in the rear pull them out slide deck out flip it over and there ya go you can do it with the deck on just jack it up
How to replace John Deere mower spindles?
Remove the mower deck. Block the blade from turning by using a piece of wood wedged between the blade and the mower deck. Loosen the nut on the top of the pulley (May require a cheater bar). Remove the pulley. If it doesn't come off easily, use a 3 armed pully remover. Once the pulley is removed, loosen the four self-tapping bolts that hold the spindle to the bottom of the deck and the spindle will fall loose. Remove the blade. Install the new spindle from below using NEW self-tapping bolts to bolt the new spindle to the deck. Replace the blade, install pulley, block blade from turning then tighten the top nut.
How do you replace a fan motor in a 1996 Saturn SL1?
Remove the two bolts at the top of the shroud, then remove shroud, fan, and motor as an assembly. Remove the One True Nut (reverse [LH] thread) that holds the fan blade to the motor. Remove the plastic-screws holding the motor to the shroud. Pull the blade off the motor. Use a hammer to disengage the motor from the shroud. Installation is reverse.
What to do when a mower blade is loose and nut is tight?
Depending on your blade - you probably sheared the shear rivets, bolts or key.
