Asked in Chrysler
How do you remove crankshaft pulley on a Chrysler 440 engine is it right or left hand thread?
Its the normal right handed thraed... It IS torqued to about 120 ft lbs though... You may need to wedge the flexplate/flywheel to keep from spinning the entire rotating assembly when you try to loosen it.
Asked in Chrysler Sebring, Pulleys
How do remove a 1996 Chrysler damper pulley?
Depending on engine displacement in general remove belt-s then bolt holding pulley to the crankshaft then using a puller remove the pulley, when installing use a installer not a hammer to put the pulley on the crankshaft. ...
Do you need special tools to remove the crankshaft damper pulley on a 1996 Mitsubishi Eclipse?
on the Chrysler engine (420a) you do need a puller and installer to deal with the crankshaft dampener pulley. ...
How do you remove the crankshaft pulley in a Chrysler pt cruiser?
The crankshaft pulley on a PT Cruiser bolts on. After removing the vehicle belt and pulley bolt, use a pulley puller to break the pulley loose and remove it. ...
How do you repair a crankshaft pulley for a 98 Saturn SC2 DOHC?
u need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removal Answer u need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removal Answer u need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removal...
Asked in Chrysler, Water Pumps, Chrysler Cirrus
How do you change a water pump on a Chrysler Cirrus?
It is fairly difficult to change a water pump on a Chrysler Cirrus. First, you remove the crankshaft pulley, remove one engine mount, take off the timing belt, and finally gain access to the pump. You can then feel free to switch them out. ...
Where is crankshaft sensor on a 1995 Oldsmobile 3800 series II engine?
It should be behind the crankshaft pulley. You'll need to remove the right front wheel and the weathershields to get to it. If you only need to test the wiring, don't remove the pulley. == == == == ...
Asked in Chrysler PT Cruiser
How do you remove the crankshaft pulley on a 2002 Chrysler PT Cruiser?
It requires a three jaw puller and a special tool that is inserted in place of the bolt. ...
Asked in Mazda 626
How do you remove crankshaft pulley Mazda 626 1993?
Im not sure which direction the bolt turns to remove the pulley...the crank shaft turns in clock wise direction when engine is running. ...
Asked in Auto Parts and Repairs, Chevy Chevelle
How do you remove a crankshaft pulley on a 67 Chevelle?
The crankshaft pulley unbolts from the harmonic balancer. The harmonic balancer can be removed from the crankshaft with a 3 bolt puller. ...
Asked in Chrysler PT Cruiser
How do you remove the crankshaft pulley from a 2005 Chrysler PT Cruiser?
You use an impact wrench or breaker bar and spanner to remove the bolt.. a special insert is placed were the bolt was. Then a three jaw puller is used to pull the pulley off. ...
Asked in Car Computers and Sensors, Mazda Trucks
Where is the crankshaft sensor located on a Mazda B2500?
Hello! The crankshaft position sensor is located behind the crankshaft pulley,on the left side facing the front of the car.It is difficult to see and to remove it you need to remove the crankshaft pulley ( radiator,belts,.... ) ...
Asked in Nissan Pathfinder
How do you remove crankshaft pulley 1997 Nissan Pathfiner?
Hello, I am copying the answer from my Nissan Pathfinder repair Manual. This is for 2.5L and 3.3 L engines, NOT THE 3.5 L ENGINE!!! 1- Disconnect Negative cable from the battery. Rause the front of of the vehicle and secure it on jackstands. 2. Remove the engine under cover. Remove the lower radiatorshroud and remove the engine colling fan. 3. Remove the drivebelts. 4. Use a strap wrench around the crankshaft pulley to hold it while using a breaker bar and socket to remove...
Asked in Mitsubishi Eclipse
How do you remove and install harmonic balancer on 2001 Mitsubishi eclipse V6?
taken from wiki Remove the cable from the negative battery terminal with a socket wrench. This ensures that you don't start the engine accidentally while removing the crankshaft balancer. Detach the accessory drive belts surrounding the crankshaft pulley to gain access to the pulley. Raise the vehicle with a floor jack and support it on jack stands. Disconnect the right front wheel with a lug wrench. Remove the fasteners for the inner splash shield on the right front fender with a socket wrench. Detach...
Asked in Honda Civic DX
Where is the crankshaft posion sensor in a 92 civic?
Remove the engine brush cover under the front of the engine. Remove the drive belt to make changing the sensor easier (optional). Remove the lower timing belt cover and the crankshaft pulley to access the crankshaft position sensor. Disconnect the electrical modules from the crankshaft position sensor, located next to the alternator. Take off the bolts with a socket wrench and remove the sensor. ...
Asked in Nissan Pathfinder, Nissan Altima
How do you remove crankshaft pulley bolt from a Nissan Pathfinder is it right or left hand thread?
1998 Nissan pathfinder crankshaft pulley bolt is right handed.
Asked in Chevy S-10
How do you replace the crankshaft pulley on a 1991 Chevy S-10 4.3L?
The pulley alone unbolts from the harmonic balancer (aka vibration damper). It's the harmonic balancer that requires a special puller to remove it from the crankshaft without doing any damage. ...
Asked in Saab
How do you replace a Saab 900s oil pump?
What year? Which engine? Generally, the oil pump is located on the front of the engine, behind the crankshaft pulley. 1) Lock the flywheel in place. 2) Remove the accessory belts and crankshaft pulley. 3) Remove the oil pump. A workshop manual will aid greatly in providing proper endfloat specs and special re-assembly instructions for the particular engine. ...
Asked in Buick LeSabre
Where exactly is the crankshaft sensor located on a '92 Buick Lesabre?
The dual Crankshaft Position (CKP) sensor is mounted to the front of the engine, attached to an aluminum bracket mounted to the left side of the engine at the timing chain cover. A 4-wire connector plugs into the sensor, connecting it to the ignition control module. Answer The crankshaft senser is located under the dampener pulley. Remove the serpentine belt. Remove right front wheel. Remove plastic access cover that's behind that wheel. With an impact wrench remove dampener pulley bolt. With an Dampener pulley...
Asked in Late Model 1979-New Ford Mustangs
How do you change crank pulley 2005 4.0 mustang?
Disconnect the negative battery cable Remove the drivebelt Remove the engine cooling fan/shroud assembly Raise the car and support it securely on jackstands Remove the power steering fluid cooler mounting bolts and position the assembly to the side without disconnecting the fluid lines Remove the crankshaft pulley bolt Use a breaker bar and socket to remove the crankshaft pulley center bolt. Discard the bolt and obtain a new one for installation.Note:It will be necessary to lock the pulley in position using a strap or chain wrench.Be...
Asked in Cars & Vehicles, Dodge Stratus
How can you get a crankshaft pulley off a 03 dodge stratus 2.4L engine?
You need a special tool to remove the crankshaft pulley on a 2003 Dodge Stratus. The correct tool is OTC Tool No. 6075. If you don't want to buy one, you can rent one from an AutoZone store. ...