Chevy Corsica

How do you remove headrest from 1993 Chevrolet Corsica?

User Avatar
Wiki User
November 16, 2013 11:03AM

how to remove headrest of 95 chevy corsica without tabs

Related Questions

User Avatar

Drain the oil from your 1993 Chevrolet Corsica 3.1 liter engine oil pan. Remove the oil pan retaining bolts. The oil pan will come off.

User Avatar

Begin by removing the positive cable from your 1993 Chevy Corsica battery. Remove the cables on the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.

User Avatar

the wire is bare how do you replace the wire with out removing the dashboard on a 1993 Chevrolet corsica?

User Avatar

29s here, i have a 92 corsica 3.1 and the ecm is located under the passengers side dash board on the side of the glove box toward the door, most likely the design didnt change so yours should be there also. the tech didnt have to remove the dash to get to it.

User Avatar

where is the trunk release button for 1993 chevy corsica

User Avatar

Remove the four bolts on the bottom of the seat back and the 2 bolts on each headrest. Take out the headrests. Lift straight up.

User Avatar

Remove the inside door panel of your 1993 Chevrolet Lumina. Remove the passenger mirror wiring harness. Remove the passenger mirror retaining bolts. Reverse the process to install the new passenger mirror.

User Avatar

bad news. the back cover has to be pulled up over the back to get at spring clips which secure the rods.

User Avatar

Most headrests that have no outside release can be removed by taking a old hacksaw blade and sliding it down the headrest shaft about 4-8 inches to release the headrest. On some the catch is on the front; others on the back; you will need to try both.Extend the headrest full up then slide the blade as far down as you can, then push the headrest AND the blade down at the same time, then pull up on the headrest only holding the blade down at the same level; the headrest will pop out; if it does not, try again. I used to remove a lot of these having sold custom seat covers for years. Some can be stubborn. I hope this helps you. Mark

User Avatar

If you have to ask how to perform this very simple, basic task, take it back to the Chevy dealer and let Mr. Goodwrench do it.

User Avatar

Remove the belt from your 1993 Chevrolet S 10 Blazer power steering pump. Remove the power steering pump hose. Remove the power steering pump retaining bolts.

User Avatar

On the left hand side of the radiator on the bottom. It's hard to get to and make sure you don't lose the drain cock because it is difficult to replace.

User Avatar

Grab the filter with your hand or a filter wrench and turn counterclockwise.

User Avatar

ok you look on the front of the block....take the thermostat cover off..then take the old one out and put the new one in and put the cover back on.....

User Avatar

Sometimes you have to remove the pump to get to the fitting on the pump.

User Avatar

It is a TH125C(3T40) 3 speed.

User Avatar

Remove the wiring harness from the back of your 1993 Chevrolet Camaro blower motor. Remove the blower motor retaining nuts. Remove the fan from the front of the blower motor. Reverse the process to install the new blower motor.

User Avatar

Ask the same question at batauto.com in the forum for transmissions. Koug

User Avatar

A 1993 Chevy Corsica can only reach 111 MPH before the factory governor will be applied....this is with the 2.2 Liter engine

User Avatar

remove the distributor cap remove the screws that attach the pick coil to the base of the distributor and replace in reverse order

User Avatar

Here check out this link http://www.autozone.com/az/cds/en_us/0900823d/80/14/98/61/0900823d80149861/repairInfoPages.htm It offers a step by step on how to do it

User Avatar

You will need to remove the inside door panel of your 1993 Chevrolet Blazer. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.

User Avatar

It is bolted to the valve body in the bottom of the Transmission. Need to remove trans pan to service them.

User Avatar

Remove the retaining ring at the top of your 1993 Chevrolet K 2500 ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.