0
What else can I help you with?
How do you change the exhaust manifold gasket on a 93 Chevy astro van?
You will need to remove the exhaust manifold retaining bolts in your 1993 Chevy Astro. Remove the exhaust manifold. Remove the exhaust manifold gasket and clean the surface. Reverse the process to install the new exhaust manifold gasket.
How do you remove exhaust pipe from manifold on ford expedition?
To remove the exhaust pipe from the manifold on a Ford Expedition, start by ensuring the vehicle is cool and safely lifted. Disconnect any hangers or brackets securing the exhaust pipe, and then use a socket wrench to remove the bolts connecting the exhaust pipe to the manifold. If the bolts are rusted or stuck, apply penetrating oil and allow it to soak before attempting to remove them. Carefully pull the exhaust pipe away from the manifold once the bolts are removed.
How do you replace the intake manifold gasket on a 87 d100 slant 6?
remove the intake and exhaust manifolds. there are bolts that attach them onto the head and there are bolts near the carburetor that attach the intake manifold to the exhaust manifold.
Is it difficult to remove exhaust manifold from 1998 jeep wrangler 4.0 engine?
Its a bit of a job because it is held on by the same bolts as the intake manifold, and the easiest way is to remove them both, otherwise the rusted exhaust bolts holding the tubing to the manifold is the worst.
How do you remove an exhaust manifold?
You just unbolt it. You first have to disconnect the exhaust pipe from the manifold then remove whatever you have to allow you to access the bolts and remove the manifold. It varies greatly from engine to engine. Some are easy and some are very hard.
Do you have to remove the intake manifold to get to the exhaust manifold on 4.0 Jeep Wrangler?
Yes, they share the same gasket and bolts.
How hard is it to replace the exhaust manifold pass side on a 2000 Ford F150 5 4L?
Chilton manual says to remove the splash guard from the fender well. Then remove the bolts from the catalytic converter to exhaust bolts. Unbolt the manifold bolts starting from the two center bolts, two rear bolts, then the two front bolts. remove the manifold. remove old gasket. replace. If you believe that then it is a relatively simple job. Good Luck!
1996 Nissan Pathfinder change exhaust manifold?
What engine???????? You should refer to repair manual if not familiar with auto repair and understand the terminology before attempting Remove nuts holding exhaust manifold to cylinder head & remove nuts/bolts holding exhaust manifold to exhaust pipes Use new exhaust manifold gaskets and install the new manifold securing the manifold to cylinder head (may need to but new nuts and or bolts) by "snugly" tightening manifold to cylinder head if not refering to repair manual
How to remove exhaust manifold on Honda Element?
To remove the exhaust manifold on a Honda Element, first ensure the engine is cool and disconnect the negative battery terminal. Remove any components obstructing access to the manifold, such as the intake manifold or heat shield. Unbolt the exhaust manifold from the cylinder head, carefully noting the order of the bolts for reinstallation. Finally, detach any remaining connections, such as the exhaust pipe, and remove the manifold from the engine bay.
How do you change exhaust gasket on 1999 grand am gt?
if the engine is a 2,4 liter, and if your replaceing the manifold gaskets, the manifold has 8 13mm bolts you need to remove, and also you need to drop the pipe, remove the 3 13mm bolts that connect to the rear pipe, then remove the four 15mm bolts that connect to the manifold, then you can remove the exhaust manifold, dont forget to remove the heat shield on top on the exhaust manifold 3 10mm bolts and one more item unplug the 02 sensor, you should be able to pull the manifold up and out of the way if your replaceing the gaskets, i just pulled the manifold off and up and bungy'd it up out of the way to clean the ports.
How do you replace exhaust manifold bolts on 2006 Dodge Durango 4.7L?
To replace the exhaust manifold bolts on a 2006 Dodge Durango 4.7L, start by safely lifting the vehicle and removing any components obstructing access to the exhaust manifold, such as the heat shield or exhaust pipe. Carefully unbolt the old exhaust manifold bolts using the appropriate socket size, and remove the manifold if necessary. Clean the threads of the bolt holes and install new bolts, ensuring they are torqued to the manufacturer’s specifications. Finally, reassemble any removed components and check for leaks before starting the engine.
How do you remove the Exhaust manifold on a 3000GT SL DOHC?
To remove the exhaust manifold on a 3000GT SL DOHC, first, disconnect the battery and remove any components obstructing access, such as the intake manifold or heat shields. Next, detach the exhaust pipes from the manifold and remove the bolts securing the manifold to the cylinder head. Carefully lift the manifold off, ensuring to check for any remaining gaskets or debris. Finally, inspect the area for any damage before installing a new manifold or reassembling.
