• American Cars
  • Ford Ranger
  • Ford F-150
  • Ford Escort ZX2

How do you remove the drive shaft from a 1996 Geo Tracker?

Top Answer
User Avatar
Wiki User
Answered 2007-08-22 20:11:08

First make drive shaft and yoke to insure tat they are replaced in the same location to maintain factory balance Remove small "U" bolts at yoke

Pry drive shaft out of yoke

Pull driveshaft off splined end

User Avatar

Your Answer


Still have questions?

Related Questions

How do you remove the crank shaft pulley on 1996 Geo metro 1.3l?

How do I remove a pully from the drive shaft. The snap ring that holds pully on has been taken off.Itried a gear puller but it bends the pully.

Can you tow a 1996 4wd jeep with a tow dolly?

You will need to remove the drive shaft to tow a Jeep with a tow dolly.

Can you remove the drive shaft from the passenger side of 1996 Plymouth breeze to replace the output shaft seal without removing the strut?

Yes. You may also remove strut & steering knucle from car without separating them (if necessary) so you do not have to get an alignment.

Replacement of drive shaft on 1996 voyger?

The front axles do not have a removable shaft, you must replace axles completly.

What is the name of the part that the drive shaft enters in the back of the rear transmission on a 1996 gm suburban?

tail shaft

Mazda 323 1.8 executive 1996 you have snapped your drive shaft but cnt get your drivers side wheel off there is a centre nut on the wheel that you cnt remove?


How do you replace speedometer cable on 1996 Geo Tracker 2 door 4wheel drive?

The 1996 Geo tracker speedometer cable is held in place by a retaining nut at each end of the cable. Loosen the retaining nuts. Remove the speedometer cable guide retainers. Reverse the process to install the new speedometer cable.

How do you change the fuel pump on a 1996 Pontiac trans am?

fuel pump is in gas tank you might have to drop your exhaust and or center support for drive shaft. to remove gas tank.

How do you remove drive shaft 1996 probe?

remove nut in center of rotor lift vehicle & separate ball joint pull drivshaft out of rotor/hub assembly as you swing spindle out of the way pull or pry out driveshaft

When was Flat Tracker created?

Flat Tracker was created in 1996.

1996 geo tracker idles good feed it gas bogs down no power?

check the timing belt. or on the 1996-1998 the crankshaft bolt comes loose and shears woodruff key in crank shaft.

How do you remove the grill on a 1996 Geo Tracker?

just pull slowly on the top until you see a gap and work it down from there

Is a 1996 geo tracker automatic 2 wheel drive flat towable?

yes put it neutral and tow from the front wheels

WHAT is the best way to remove a front cv drive shaft from a 1996 jeep grande Cherokee?

I am sure there are proper tools on the market, but I had to do "emergency replacement" in my driveway. I used a pry bar and a hammer for removal - worked okay.

Where can you find an ehaust manifold for a 1996 tracker?


What is causing my 1996 Jeep Cherokee Front Drive Shaft Noise?

The universal joints in the front driveshaft may be going bad.

Where is the vss located on a 1996 Chevy Tahoe?

If it is a 4-wheel drive then it is screewed into the transfur case, if it's not then it will be on the transmission tail shaft.

How do you remove and install a fuel pump for a 1996 Chevrolet S10?

You have to unbolt the truck bed and raise it about 12 inches and access the pump between the frame and the bottom of the bed. You cannot drop the tank from the because of the drive shaft and exhaust system. Even with the drive shaft and exhaust out of the truck, you still have to take apart some of the frame to drop the tank. It's much easier to raise the bed.

How do you remove the interior door panel on 1996 Geo Tracker?

there are screws in the mirror panel and under the arm rest and the rest are tabs that pull off

Where is the obd-II connector on a 1996 tracker?

The 1996 GEO Tracker OBD 2 port is on driver side dash next to center console

Does a 5speed 1996 Geo Tracker have power steering?

Yes it does. I have a 96 geo tracker and it does have power steering.

How can you remove and install a 1996 Ford Taurus 3.0 engine with a floor shift and 4 wheel drive transmission?

1996 Taurus never equipped w/ 4 wheel drive

Where is the alternator located on a 1996 Geo Tracker?

The alternator, facing the engine, is located low on the left side of the engine. It really is easier to remove and replace from the bottom.

What is the difference between a 2 joint shaft and a 3 joint shaft for a 1996 Dodge Dakota?

The joint you are looking for is the U joint. You have one at the back of the transmission and another where the drive shaft attaches to the rear end. On the extended version there will also be a U joint in the middle. So if you look under the car and the drive shaft just looks like one long tube you have a two joint shaft. If however, you see what appears to be a joint about the size of both of your fists together in the middle of the shaft, you are looking at the third joint.

How do you replace half shaft on a 1996 dodge neon?

1.remove the wheel (i assume you are capable of using a jack if you are asking how to change the shaft) 2.remove the brake caliper and rotor 3.unbolt the strut from the spindle and tilt the spindle out (may have to unbolt from the lower control arm) 4. slide shaft out of the wheel bearing hub 5. pull the shaft out of the transmission. install is reverse of the above steps