0
How do you remove the hard top from a Mercedes SL without any power?
Wiki User
∙ 16y ago
Power is not normally involved. There are some crank hoists (and yes power ones) that you can purchase, which if you have a high enough space to attach them, then have straps that go around the top and lift it. But all that does is get it hanging up there! The carts they make for storing and moving them are very handy though. Any MB accessory place or Ebay for sources.
These are heavy suckers! 2 people please!
Basically same as lowering soft top.
Release the rear securing latch, using the lever behind drivers door.
Release the 2 twist secure point up front, using the separate handled provided to do so. (Commonly tossed in glove box).
There may be some wires to unclip on the passenger side, if you model has rear window heat or such).
One person each side and up she comes! Sure, there is a rubber gasket on front and back that may be a little sticky. I recommend the 2 people agree to lift together, and then walk together with it toward the rear of the car in one motion....you want to avoid bouncing or putting it back down on the car paint.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How do you remove the inside mirror from a Mercedes?
pull it down hard pops out
Can you just remove the steering pump on an 87 Saab 900 you do not like the power steering and wonder if the linkage is strong enough to function without the power steering pump?
You can not remove a power steering pump on your car and expect it to handle like a car with out power steering. Removing the pump will make it very hard to steer because the rest of the steering components are made for power steering.
What is the meaning of the word entrenched?
"Entrenched" means firmly established and difficult to change, typically referring to beliefs, practices, or systems that have been in place for a long time. It can also imply being deeply ingrained or well-established within a particular context.
Why is my Mercedes ml320 so hard to steer?
Make sure your power steering is topped off, if it isn't try and find out where it is leaking from and repair it
How hard is it to turn without power steering?
It is not hard at all. I have a 1995 coupe and don't have a problem at all in city traffic.
Mercedes-Benz 300e hard to start?
2004 mercedes benz tuneover but want start
Can you steer power-steering car without power?
Yes it is just very hard to turn the wheel when you slow down
How do you remove the front driver's side power window motor and install a new one?
Here are complete step-by-step instructions (with photos) on how to remove a door panel: http://www.ricksfreeautorepairadvice.com/repair-topics/window-power-repair/remove-a-door-panel-from-any-vehicle-without-a-diagram Here are complete step-by-step instructions (with photos) on how to test a power window motor to determine whether the problem is in the motor/regulator or the switch/wiring http://www.ricksfreeautorepairadvice.com/repair-topics/window-power-repair/replace-a-power-window-regulator Hey Chris==This is very hard on some makes as the door panel is hard to remove. After you get it off, you have to remove the motor which is attached to the window linkage which is under spring preasure. There are very sharp edges in the door so be careful. GoodluckJoe
Why Does your Computer go quiet when you unplug it?
Because without power, the hard drive, the fan, they make noise when they have power. Without it, they all stop making the computer go "quiet."
How do you remove a partition on a hard drive running Windows 2000 without reformatting the hard disk?
There are several partitioning products available that are easy and intuitive to use.
How do you remove the valve cover gasket from a 1992 Mercedes-Benz 190E?
remove the 10mm bolts from the edges and clean all surfaces VERY CLEAN and replace gasket and then torque the bolts back not sure of the lbs to torque to good luck it is not hard to do
How do you remove the valve cover gasket from a 1992 Mercedes Benz 190E?
remove the 10mm bolts from the edges and clean all surfaces VERY CLEAN and replace gasket and then torque the bolts back not sure of the lbs to torque to good luck it is not hard to do
