answersLogoWhite

0


Best Answer

Most headrests that have no outside release can be removed by taking a old hacksaw blade and sliding it down the headrest shaft about 4-8 inches to release the headrest. On some the catch is on the front; others on the back; you will need to try both.Extend the headrest full up then slide the blade as far down as you can, then push the headrest AND the blade down at the same time, then pull up on the headrest only holding the blade down at the same level; the headrest will pop out; if it does not, try again. I used to remove a lot of these having sold custom seat covers for years. Some can be stubborn. I hope this helps you. Mark

User Avatar

Wiki User

โˆ™ 2005-11-27 14:11:55
This answer is:
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you remove the headrest form a 1993 Mazda b2200 pickup?
Write your answer...
Submit
Related questions

Can you put a 2.8L Nissan engine in a 1991 Mazda B2200 pickup?

no


Torque specs for head bolts on a 1990 Mazda b2200 pickup truck?

The torque specs for the cylinder head on a b2200 are 59-64 ft lbs (cold).


What 2008 Mazda engine will fit your 1989 Mazda B2200 pickup?

A 1995 KIA Sportage 2.0L 16v DOHC will bolt right into the B2000 and the B2200. You will have to get a system called megasquirt from www.diyautotune.com Your Horse Power will be almost double that of the B2200 2.2L SOHC


Where is the location of the water pump on a 1990 Mazda B2200 pickup?

behind the radiator,in the middle of the engine


What size are the front speakers in an 89 Mazda b2200?

The front dash speakers in the 89 Mazda b series pickup trucks are 4".


Is there a 17in chrome spoke wheel to fit a 6x139.7 pattern lowered 1990 B2200 Mazda pickup?

-


How much pressure on electric fuel injection fuel pump for 1992 b2200 Mazda pickup?

92 b2200 ,fuel injection psi should be 38 to 46 psi


What could cause hesitation when stepping on accelerator pedal in a 1998 Mazda B2200 pickup?

My 89 B2200 does this. Its like there is a dead spot in the acceleration. It is because the accelerator pump is leaking.


Where does the in line fuel filter go in a Mazda B2200 pickup?

it con-nets to the fuel pump and the gas tank


Where is the fuel pump relay on 1992 b2200 Mazda pickup?

This should be located under the left drivers side kick panel.


Where is the fuel pump on a 1992 Mazda b2200 pickup?

MY 1992 MAZDA B2200 PICKUP RUNS GREAT FOR A SHORT TIME AND THEN SEEMS TO STARVE ITSELF WHEN I GO TO GIVE IT FUEL ALMOST TO THE POINT WHERE IT WON'T RUN IF I TURN THE ENGINE OFF FOR A FEW SECONDS IT WILL GO GOOD AGAIN BUT ONLY TO REPEAT THE PROBLEM OVER AGAIN


Would the flywheel of 1989 Mazda B2200 fit a 1984 Mazda b2200?

No


Where is the EGR valve located on a 87 Mazda B2200?

where is the EGR valve on a 1989 mazda b2200


What are the specs for valve adjustment on a 1986 Mazda B2200?

Who is a valve calibration for mazda b2200 1988


Where is the gas filter 1991 Mazda b2200 pickup truck?

Look under vehicle follow fuel line from tank


Where is the fuel pump on a 89 Mazda b2200?

where is the fuel pump on a 89 Mazda b2200


Where is temp sensor on 89 Mazda b2200 pickup?

Coolant temperature sensor is locatedat the front of the intake manifold near the upper radiator hose.


How many gallons of gas does a 1992 Mazda B2200 hold?

The 1992 Mazda B2200 will hold close to 17 gallons of gas. The 1992 Mazda B2200 is a four-cylinder vehicle.


Where does the in-line fuel filter go in a Mazda B2200 pickup?

behind the fuel tank you will see a clamp this is where the filter goes at least it is there on my 1989b2200


Where does the wire from the automatic choke hook to on a 1988 b2200 Mazda pickup?

it connects to any positive(hot wire) terminal controlled by key.


What type freon used in a b2200 mazda pickup 1990?

Was built with R12Was built with R12


Why would a 1987 Mazda b2200 pickup smoke all the time and not be the rings?

The valve guides in the cylinder head wear out and oil gets sucked in and burned.


How do you replace fuel pump 92 Mazda pick up B2200?

How do you replace fuel pump 92 Mazda pick up B2200?


Is a 1988 Mazda B2000 a 4 cylinder?

Yes, a Mazda B2000 is most definitely a 4-cylinder with a 2.0L engine. However, technically Mazda didn't produce the B2000 as a 1988 model. It was made in 1986-1987. Then in 1989 Mazda made the B2200 Pickup, which is a 2.2L 4 cylinder.


Where is the ignition module located on a 1989 Mazda b2200?

where is the ignition module located on a 1988 Mazda b2200