answersLogoWhite

0


Best Answer
Copy

Disconnect batter ground cable. Remove the upper and lower steering column shrouds. Remove lock screw and disconnect ignition switch electrical connector. Rotate the ignition switch to the RUN position. Remove the two screws retaining ignition switch. Disengage ignition switch from the actuator. When installing new key set, ensure new key set is in the RUN position prior to installion.

User Avatar

Wiki User

โˆ™ 2015-07-15 19:15:38
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you remove the ignition lock cylinder from a 1996 Ford Thunderbird?
Write your answer...
Submit

Related Questions

How do you replace ignition lock cylinder on a 1996 Mercury Tracer?

Begin by removing the retaining ring at the top of your 1996 Mercury Tracer ignition switch. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the cylinder. Reverse the process to install your new ignition lock cylinder.


How do you remove ignition switch 1996 cougar xr7?

Insert the key into the ignition. Push the release/switch button at the bottom of the cylinder, and pull the cylinder out.?æ


Where is the ignition control module on a 1996 Ford Thunderbird?

It is in the dist.


How do i replace the ignition lock cylinder on 96 silverado?

Begin by removing the retaining ring at the top of your 1996 Chevrolet Silverado ignition lock cylinder. Slide the ignition lock out and remove the wiring harness. Reverse the process to install your new ignition lock cylinder.


How do you remove the ignition key cylinder in a 1997 Virago?

i have a 1996 varago..to remove the ignition switch you must remove the head light Lind's and all that is inside will be able to see the screws that holds the switch in


How to replace ignition key cylinder for 1996 Pontiac sunfire and recheck theft deterent and code new key cylinder to vehicle?

how to remove key cylinder on 98 sunfire


How do you remove an ignition cylinder on a 1996 BMW 328i?

This is a sping lock DIY video and explains very well in this video how to remove your ignition, hope it helps http://www.youtube.com/watch?v=tETEtb5Yr_o


How do you remove the key from the lock ignition?

1996 rodeo- how to remove key from lock ignition?


How do you change the ignition cylinder on a 1996 Chevy Astro?

==This operation requires special tools.== Remove the steering wheel, and tilt assembly, you can then see a black screw above the rounded area for the lock cylinder, remove this screw and the cylinder will then pull out.


Ignition module location 1996 ford thunderbird 4.6?

The Ignition Control Module on a 1996 Ford Thunderbird 4.6 is located inside the EFI or Electronic Fuel Injector. The EFI is the carburetor. Look for a cord that has a connector that resembles an HD Cable.


How to fix a 1996 Pontiac grandam ignition locked?

Replace the ignition lock cylinder.


What is the size of the fuel tank in a 1996 ford thunderbird 6 cylinder?

18 gal.


Where is the ignition control module on a 1996 3.8L Thunderbird with the distributorless ignition system?

the little gray box on top the a.c. compressor or by the radiator.


Can you put a 1994 thunderbird motor in a 1996 thunderbird?

Can you put a 1994 thunderbird motor in a 1996 thunderbird?


What does engine code 303 on a 1996 ford thunderbird mean?

An engine cylinder misfire has been detected in the # 3 engine cylinder


Where would the ignition module located in a 1996 46 fuel injected thunderbird?

its usally located up your bum


Which fuse is for the ignition on a 1996 Thunderbird lx?

Mine is in the spot numbered 16. Its a 60a fuse, big and yellow...


How do you pull out a ignition cylinder from a 1996 S-10 extented cab automatic?

how to pull a ignition cylinder on a S-10 extented cab automatic


How do you take the Ignition Lock Cylinder out of a 1996 Chevrolet Cavalier?

Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder


How do you change a ignition cylinder on a 1996 Chevy cavalier?

Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder


How do you replace the ignition lock cylinder on a 1996 Cavalier?

Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder


How do you change an ignition cylinder on a 1996 Chevrolet Cavalier?

Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder


How do you replace the ignition lock cylinder on a Pontiac Sunfire 1996?

Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder


How to remove the ignition switch from a 1996 Geo Metro?

screwdriver


How can you remove an ignition switch from a 1996 Subaru Outback?

yes