answersLogoWhite

0


Best Answer
Copy

The 1994 Pontiac Grand Am ignition lock cylinder is held in place by the retaining ring at the top of the cylinder. Remove the retaining ring. Remove the wiring harness from the back of the cylinder.

User Avatar

Wiki User

โˆ™ 2014-09-18 00:23:14
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you remove the ignition lock cylinder on a 1994 Grand Am?
Write your answer...
Submit

Related Questions

How do you remove and replace an ignition lock cylinder on a 1994 Ford Bronco?

Begin by removing the retaining ring at the top of your 1994 Ford ignition lock cylinder. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the ignition lock cylinder. Reverse the process to install your new ignition lock cylinder.


Can you replace the ignition lock cylinder on a 1994 Pontiac firebird without removing the steering wheel?

You can replace the ignition lock cylinder in your 1994 Pontiac Firebird without removing the steering will. Remove the retaining ring at the top of the ignition cylinder. The ignition cylinder will slide out.


How do you remove the ignition lock cylinder from a 1994 Ford Thunderbird with out a key?

rip it out or call a locksmith it happened with my 94 tbird


If you remove all the tumblers from the ignition lock cylinder on a 1994 Saturn SC2 can you still start and drive the car but just not have a lockable ignition and steering wheel?

Should be correct


How do you change the key ignition on an 1994 Mighty Max?

remove the shroud covering the steering coloum and turn the key to the on position push in release pin over ignition and pull cylinder out.


How do you replace ignition switch for a 1994 Chevy Corsica?

Remove the retaining ring at the top of your 1994 Chevy Corsica ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.


Where is the fuel line rail on 1994 Pontiac Grand Am 6 cylinder engine?

underneath the upper intake you need to remove the upper to service it


How do you replace the ignition switch on a 1994 Camaro?

disconnect battery. remove steering wheel. remove turn signal switch. remove the buzzer switch with nedle nose pliers. then place key in ignition and set to lock position. remove lock cylinder retaining screw. then pull cylinder straight out.disconnect passkey connector from bulkhead and remove retaining clip.use a wire to aid in installation of pulling harness through column.


How do you remove a broken key from cylinder on 1994 Toyota 4Runner?

Locksmiths have special tools and can remove broken keys from cylinders. Is the cylinder in a door or the ignition? First, make sure the lock is in the off position for ignition or the verticle position for a door. Then shoot in alot of lubricant. Next wiggle and jiggle the key while pulling gently. If not possible, take to locksmith.


Is there a certain position the electrical ignition switch for a 1994 Explorer has to be set to for the key cylinder to work properly?

If you are talking about installing or removing the ignition lock cylinder I believe the key has to be in the run position.


Does a 1994 Ford Ranger have a distributerless ignition?

In 1994 the 2.3 L 4 cylinder and the 4.0 L V6 engines are DIS ( distributorless ignition system ) The 3.0 L V6 was from 1995 on


How do you remove the key cylinder on a 1994 BMW 325i?

verry carfully


How involved is it to change a headgasket on a 1994 ohc 2.3l grand am?

alot involved if your not on hands with cars i wouldn't recommend it have to remove cylinder head, intake and exhaust manifolds and remove timing chain and covers, time consuming


Where is the ignition module on a 1994 grand marquis?

L/H REAR OF ENGINE COMPARTMENT ON FENDER


1994 Plymouth acclaim and the ignition cylinder was popped but it still starts with the key Do you need to replace the cylinder to pass safety?

not in the state of new york


Need to know how to replace a master cylinder with abs brakes on a Pontiac grand am?

my husband is trying to replace the master cylinder on a 1994 grand am. he was wondering on how to align the gears for the abs.


How do you remove the ignition lock cylinder from a 1994 Ford Ranger?

do you have the key!!!! remove the steering wheel covers turn the key to run there should be a little brass pin under the lock cyl push it in and pull out cyl if no key you have to drill out the tumblers.


Where is the ignition control module on 1994 Ford Van E250 6 cylinder?

ignition module is found behind battery box right hand side


How do you remove the steering column bearings on a 1994 ford F350?

remove column dust covers, along with ignition switch. then remove retaining


Where is the ignition module on a 1994 3.3L Pontiac Grand Prix?

Under the dash attached to the steering column.


How do you remove and install a 1994 Mercury Grand Marquis LS heater core?

You must remove the dash.


How do you remove the cylinder from the back brakes on a 1994 Pontiac Grand Am husband says they are too big to get off?

some may have a spring clip or two bolts and brake line but is not to big of a job


How do you remove power steering pump 1994 grand am?

hire a good mechanic


Ignition timing on 6 cylinder 5 speed 1994 Toyota 4 runner?

10 degrees before TDC


How do you get the piston out to change the back disc brakes on a 1994 Pontiac Grand Prix?

You don't remove the piston, you just compress it. Loosen the cap on the master cylinder and then compress the piston all the way in. You can then remove the old pad and install a new one.