Chevy Corvette
Pontiac Aztek
1995-2005 Chevy Cavaliers

How do you remove the ignition switch not lock on a 1973 Chevy Corvette?

454647

Top Answer
User Avatar
Wiki User
Answered
2006-08-01 00:22:21
2006-08-01 00:22:21

switch should be on the bottom of the steering column ,probably have to drop the two bolts on console to get to it

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


Remove the retaining ring from the top of your 1989 Chevy Corvette ignition switch. Slide the ignition switch out and remove the wiring harness.

Remove the retaining ring from the top of your 1999 Chevy Cavalier ignition switch. Slide the ignition switch out and remove the wiring harness from the end of it.

Remove the retaining ring at the top of your 1985 Chevy ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.

You will need to remove the retaining ring at the top of your 1998 Chevy Lumina ignition switch. Slide the ignition switch out. Remove the wiring harness.

how to remove key stuck in ignition switch in Chevy colbalt

Remove the retaining ring at the top of your 1994 Chevy Corsica ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.

how do you remove the ignition switch on a 1990 chevy half ton pick-up?

You will need to remove the ignition switch retaining ring in your 2002 Chevy Astro Van. Slide the ignition switch out. Remove the wiring harness from the end of the ignition switch. Reverse the process to install the new ignition switch.

You will need to remove the retaining ring from the top of your 1997 Chevy Camaro ignition switch. The ignition switch will slide out. Remove the wiring harness. Reverse the process to install the new ignition switch.

Chevy Tahoe Ignition Key Starter Switch

i have a 06 Chevy cobalt and can't get the key out of the ignition switch

Begin by removing the retaining ring at the top of your 1992 Chevy ignition switch. The ignition switch will slide out. Remove the wiring harness from the end of the ignition switch. Reverse the process to install the new ignition switch.

The 1966 Chevy Impala ignition switch can be removed by loosening the retaining ring at the top of the ignition switch. Remove the wiring harness. Reverse the process to install the new ignition switch.

Remove the ignition switch retaining nut. Pull the ignition out. Remove the wiring harness from the back of the ignition barrel. Reverse the process to install the new ignition.

The 1985 Chevrolet El Camino ignition switch can be removed by loosening the retaining ring at the top of the switch. The switch will slide out. Remove the wiring harness from the back of the ignition switch.

Follow the large purple wire from the ignition swiych to the neutral safety switch or the clutch switch and check the power. You may not need to replace the ignition switch.

You will need to remove the retaining ring from the top of your 1989 Chevrolet blazer ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.

Remove the retaining ring at the top of your 1993 Chevrolet K 2500 ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.

To remove the igniton lock, remove the steering wheel and turn signal switch housing. From there you will be able to see the lock which holds the ignition lock into place. slide a screwdriver into the slot and apply pressure. The igntion lock can then be pulled out.

If you need to remove your ignition switch, you should consult your owners manual. Check for a guide on how to remove and replace and follow the instructions.

You can remove the 2000 Chevrolet Astro Van the ignition switch cylinder by removing the retaining ring. The retaining ring will need to be turned to the left. The ignition switch cylinder will slide out.

With no key you will have to drill out the existing tumbler assembly from the switch in order to unscrew the ignition switch bezel.

You will need to remove the retaining ring at the top of your 1978 Chevrolet Blazer ignition switch. Slide the ignition barrel out and remove the wiring harness. Reverse the process to install the new ignition switch.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.