0
What else can I help you with?
Where is the jack 2004 Honda Odyssey?
Open the tailgate. Remove the cargo net.The tools and jack are behind a cover in the cargo area on the driver's side. Remove the cover by turning the handle counterclockwise, then pulling out the cover.Take the tools out of the storage compartment.Turn the jack's end bracket counterclockwise to loosen it, then remove the jack.
How to remove the inside door panel of a 2004 Hyundai Elantra to fix the inside handle?
1. On manual windows remove the crank handle by dislodging the clip 2. Remove the outside mirror cover 3. Detach the door handle trim piece and disconnect the linkage rod. Remove the door pull mounting screw. Unplug the electrical connector from the power window switch 4. Remove the retaining screws and detach the panel by carefully prying it away from the door. Remove the screw concealed behind the armrest and one behind the door handle. Pull the panel upwards to remove it 5. For access to door outside handle raise the window fully remove the power window control unit the door panel bracket and speaker then carefully peel back the plastic water shield
How do you remove front rotors on a1999 ford crown Victoria?
Remove the front wheel then remove the 2 caliper bracket bolts behind the rotor and the rotor should slide off.
How can I remove a Delta shower handle that does not have a set screw?
To remove a Delta shower handle without a set screw, look for a small hole or slot on the handle. Insert a flathead screwdriver or an Allen wrench into the hole and twist counterclockwise to loosen and remove the handle. If there is no hole or slot, try gently prying the handle off with a flathead screwdriver or a handle puller tool. Be careful not to damage the handle or the surrounding area.
Where is the airbag sensor for Honda civic 2000?
behind the center console behind black panel mounted on floor bracket. remove to black panels from right and left side.
You have removed power steer pump pulley and all thevisible bolts in an attempt to remove the power steer pump bracket that covers 3 bolts on the water pump can not get bracket off?
You might need to remove the power steering pump, on my jeep there is a bolt behind the pump that also secures the bracket to the engine. what you working on
How can I remove a threaded bottom bracket from a bicycle?
To remove a threaded bottom bracket from a bicycle, you will need a bottom bracket tool that matches the specific type of bottom bracket on your bike. First, remove the crank arms and then use the bottom bracket tool to unscrew the bottom bracket from the frame in a counterclockwise direction. Once it is loose, you can remove it from the frame.
How can I remove a threaded bottom bracket from my bicycle?
To remove a threaded bottom bracket from your bicycle, you will need a bottom bracket tool that matches the specific type of bottom bracket on your bike. First, remove the crank arms and then use the bottom bracket tool to unscrew the bottom bracket from the frame in a counterclockwise direction. Once it is loose, you can remove it from the frame.
How do you remove the T-Tops From a 1981 Corvette?
Remove the large bolt behind the visor,then move the handle down that unlocks the roof.
How can I remove a bottom bracket?
To remove a bottom bracket, you will need specific tools such as a bottom bracket tool and a wrench. First, remove the crank arms and then use the bottom bracket tool to unscrew the bottom bracket from the frame. Be sure to follow the specific instructions for your bike's bottom bracket type.
How do you repair the passenger side door handle on a 1997 Chevy Cheyenne pickup?
You must replace the handle, they are made of plastic. For the inner- remove both screws in the door panel[in the grab handle] remove the trim from the door handle. Remove window crank and with proper tool remove door panel. Tool is cheap. With panel off, there will be one rivet holding old door handle in place. Drill out rivet [ 3/16 ] and slide whole door handle assembly forward. Carefully remove door and lock rods and reverse the process to assemble. Outer- One bolt is behind door panel and the other is on the outside edge of the door right behind the handle. Simply remove bolts, remove handle and swap door lock into new handle and replace.
How do you remove 1968 Chevy impala window crank?
Your local auto parts store will sell you an inexpensive tool for under $10 to remove the clip from behind the handle to release handle from door.
