You must remove the plastic "buttons" holding the trunk lining (flathead screw driver). Remove enough to get lining out of the way to have access to the back of the tail light assembly.
Remove the wiring harness from the high mount brake light. Remove the back cover of the brake light assembly. Take hold of the brake light connector, push in and turn at the same time. Reverse the process to install the new brake light.
remove bulb from in side the boot
The brake light assembly can be access through the cargo compartment. Remove the cover to the brake light assembly. Take hold of the brake light connector, push in and turn at the same time. The brake light will come out. Reverse the process to install the new brake light.
You can access the brake light bald through the trunk compartment. Remove the trunk liner from the tail light assembly. Push the brake light connector in and turn at the same time. The brake lightbulb will come out. Reverse the process to install the new brake light
A brake light on a 1999 VW can be accessed through the rear of the vehicle. Locate and remove the plastic covers for the light housings. Remove the bulbs. Replace with new units.
In the top of the trunk near where the brake light is located, there is a small plastic window, remove it and you access the light bulb.
The center section of the upper area of the that encloses the upper light assembly needs to be removed. It is plastic and is clipped in so be careful. After you remove this section the light assembly may or may not be attached to this piece. You need to unattach it and remove the bulb which is a 21 18W D bulb, standard rear brake light bulb in most American cars. Replace bulb and replace assembly then reclip the plastic section to the door. Be careful the plastic clips can break.
you remove plastic red/white cover with 2 screws and remove bulbs.
I have a 95, which is obviously a different body type... but on mine you have to remove the plastic trim along the inside of the trunk behind the brake light assemblies. From there you can remove the plastic clips that hold various parts of it on.
Open trunk remove 2 plastic push pin remove cover
To change brake light bulbs on a 1998 Lexus ES300, open the trunk lid. Locate the plastic rivet on the side of the trunk liner. Turn the rivet while pushing in with a screwdriver. Remove the rivet and the trunk liner can be pulled away to access the bulb. Push in and turn the bulb to remove. Insert the new bulb the same way. Replace the rivet in the trunk liner.
Follow the link below, labeled "How to replace a Lexus IS300 tail light"
go in your trunk and there are covers where the brake lights are...remove covers, unscrew plastic nut, and remove light...
To change the brake lights on a 1997 Volkswagen Polo first locate the brake light housings in the trunk. Remove the plastic covers and unlock the bulbs. Remove the bulbs and install the new brake lights.
Inside the trunk behind where the brake lights are are a plastic cover. Remove that and you will see one bolt. Reach in to the far side of the light and you will find the second bolt. Remove those and the brake lights can be pulled out. Now just twist the bulb holders and there are your brake light bulbs.
Its the parking brake light.
You can access the brake light assembly from the cargo compartment of your 1998 Dodge Neon. Remove the wiring harness from the back of the brake light. Remove the brake light retaining bolts. The brake light will come out. Reverse the process to install your new brake light.
there is a plastic cover above the tail light held on by two screws. remove that and simply pull the tail light out.
I just replaced mine and it's super easy. Get a pair of pliers. Get on the back seat and face the third brake light. With you hand, push the brake light assembly to the left, as far as it will slide. On the right of the brake light you will see a little groove in the carpet. This groove is for your finger to pop the light out, it pops out easily. Then unplug the electrical cord. Take the pliers and gently turn the plastic piece holding the bulb and it will come out of the plastic housing. Be careful when turning because it's plastic and you don't want to damage it. You may have enough strength in your finger to turn the plastic. After you turn and remove the plastic piece holding the bulb, you simply remove the bulb with your finger (it's a Toyota bulb). I took the bulb to the Toyota dealer for a replacement. After replacing the bulb and turning it's plastic holder back in the third brake light assembly, reconnect the electrical plug, then snap the assembly back in place. If you have the bulb ready, you can complete the whole job in 3 minutes. Good Luck!
Lexus IS300 3rd brake light is changed from the back seat. Pry the light up and disconnect wiring. Replace bulb and put back together. Easy job
i assume it is the brake light that is inside the car above the parcel shelf. You will need to get a screwdriver and on the underside of the brake light there will to two holes - inside are the screws (they are there), Remove the screws and then carefully lift the plastic cover up and out of the way. Now remove the blown bulb and replace.
You will need to remove the 1998 Chevy Camaro brake light wiring harness. Remove the brake light retaining screws. Reverse the process to install the new brake light.
The center brake light replacement will require replacing the entire brake light assembly. Remove the wiring harness. Remove the center brake light retaining screws. Reverse the process to install the new center brake light.
Open the trunk. In there, remove the 5 nuts holding the tail light bezel in place. That allows you to lift off the whole red plastic bezel from the outside. Twist brake light socket about 1/4 turn, and pull it straight out.