0
How do you remove the staked nut on the rear spindle of a 2000 Nissan to remove the brake rotor?
Wiki User
∙ 8y ago
Drive a screwdriver or flat punch into the stake groove to peel the flare back on the nut. Use and impact gun or a breaker bar to do the rest.
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
How do you replace a hub bearing for a ford escort 1996 1.9 liter?
To replace the rear hub bearing you: 1. Jack up the wheel and support it with a stand. 2. Remove the brake drum and shoes. 3. Remove the cover on the spindle. 4. Raise the staked portion of the spindle nut with a hammer and punch. 5. Remove the nut. 6. Unbolt the strut from the spindle. 7. Unbolt the trailing link from the spindle. 8. Unbolt the lateral links from the spindle. 9. Take the spindle and bearing to a machine shop. The old bearing must be pressed out and the new bearing pressed into the spindle.
How do you replace brake pads on a 1992 Nissan Stanza?
You will need to remove the tire and wheel from your 1992 Nissan Stanza. Remove the brake pad spring and caliper. The brake assembly will come off. Reverse the process to install the new brake pads.
How to change the rear hub assembly on a 1999 ford escort sedan?
1. Loosen the lug nuts on the side you want to change. 2. Chock the front wheels. 3. Jack up the car. 4. Take off the wheel. 5. Work the dust cap off with a chisel enough to get a pair of pliers around it. 6. Pull the dust cap off with pliers. 7. Remove the brake drum and shoes. 8. Raise the staked portion of the spindle nut with a punch and hammer. 9. Remove the nut. 10.Remove the backing plate. 11.Unbolt the strut from the spindle. 12.Unbolt the trailing link from the spindle. 13.Unbolt the lateral links from the spindle. 14.Remove the spindle.
How do you remove brake drums on a 1989 Nissan sentra?
very carefully :)
Where is the brake spindle located?
The brake spindle goes through the center of the rotor. You will see it when rotor is removed.
How do you change the front rotors on a 1996 Chrysler Sebring?
Step one is to remove the tire. Step two is to remove the brake caliper. Step three is to remove the cap that covers the spindle the rotor is spinning on. Step four is removing the bolt holding the rotor on the spindle. Step five is pulling the rotor off the spindle.
How do you remove the brake light on a 2010 Nissan altima?
smash it in wi a hammer
How do you change the front brake rotor on a 1997 f 150 4X4?
you have to press the wheel studs out of hub after you remove it from the spindle
How do you remove the front spindle from 1986 fiero gt?
Jack up and safely support car Remove the following component's: Wheel, Brake caliper, brake rotor. Disconnect tie rod from spindle Support lower "A" arm with stand etc Remove nuts for upper and lower ball joints. Use an appropriate tool to release the ball joints from the spindle, do not use a fork and hammer as this will damage the joint, there are special tools available for this purpose. Once the joints are released you should only have to heave to get the spindle out.
How do you remove a brake rotor in 1988 Chevy four wheel drive?
1.get the tire off 2.remove the locking hubs 3.this is where you are going to need a special spindle nut socket in order to remove the spindle nuts (where to get one of those im not sure but i think Napa or Autozone would sell something like that.) 4.after you get the spindle nuts off you remove the calipers
How to remove and replace front brake rotors on 1999 Nissan frontier?
how to remove front rotors on 2003 Nissan fronter 4 wheel drive pick up
How do you change front wheel bearings on a 1999 Grand Pr ix SE?
TO CHANGE THE WHEEL BEARING ASSEMBLY YOU NEED TO REMOVE THE WHEEL THEN LOOSEN THE SPINDLE NUT. REMOVE THE BRAKE CALIPER AND BRAKE ROTOR, ON THE BACK OF THE BEARING ASSEMBLY REMOVE THE THREE BOLTS THAT HOLD IT IN PLACE. UNPLUG THE WHEEL SPEED SENSOR IF APPLICIBLE. REMOVE THE SPINDLE NUT. THATS THE BEST I CAN REMEMBER, ITS BEEN A WHILE.
