0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How are the vehicle doors removed from the end-panel frame?
first remove the hinge pin from the top of the door header
Can you replace top door hinge with bottom hinge on 1992 ford explorer?
You can replace the top door hinge with bottom hinges on the 1992 as long as the hinge is for the cab doors. The hinges for the tailgate would not work on the doors.
How do your remove a double action hinge door?
unscrew the plate at the bottom and slide lower end along the floor until the pin at the top can be clear of the indent at the top of the door. Now the door should be clear and unattached!
How do you remove driver door on 1967 gto?
Open the door and find something to put under the bottom of the door to support it's weight. Remove the bolts that fasten the door to the door hinge, remove the top one last and be sure to have a firm grip on the door when you take the last bolt out so you don't drop the door.
What kind of hinge is needed for two panel door to fold back completely onto one panel?
the hinge is a bolt in the door at the top and bottom and the door slides on a track
What is a door hinge pin?
A hinge pin is a pin that holds together two hinge plates, one of which is fastened to the door and the other is fastened to the door jamb. There are usually two or three hinge assemblies used on each door, one near the top, one near the bottom, and sometimes one at the middle.
What is a door hinge?
A hinge pin is a pin that holds together two hinge plates, one of which is fastened to the door and the other is fastened to the door jamb. There are usually two or three hinge assemblies used on each door, one near the top, one near the bottom, and sometimes one at the middle.
How do you change door pins and bushings on a 1999 Chevy blazer?
REMOVAL & INSTALLATIONSee Figures 1 and 2 Fig. 1: A spring compressor tool must be used to remove the springs when working on the doors/hingesFig. 2: Exploded view of the door hinge pinsThe following procedure requires the use of a door hinge spring compressor such as J-36604-A or equivalent. # If equipped with power door components, perform the following procedures: ## Disconnect the negative battery cable. ## Check for access to the wiring by removing the cowl side vent cover. If access is possible, remove the receptacles from the wiring harness, then remove the retainer from the wiring harness grommet. Remove the rubber conduit from the door pillar by pushing it from the vent cover side. ## If access is not possible, remove the door trim panel, then unplug the electrical harness connector from the power door lock motor and/or the power window regulator. Remove the harness from the door. # If available, apply cloth-backed tape to the door and body pillar for protection. CAUTIONBefore removing the hinge spring from the door, cover the spring with a towel to prevent the spring from flying and possibly causing personal injury.# Using a door hinge spring compressor such as No. J-36604-A or equivalent, compress the door hinge spring and remove it. # To remove the door hinge pin clips, spread the clips and move them above the recess on the pin; when the pin is removed, the clip will ride on the pin and fall free of it. ## Using a soft-head hammer and a pair of locking pliers, remove the lower pin from the door hinge; then, temporarily install a bolt (in the lower pin hole) to hold the door in place until the upper hinge pin is removed. ## Remove the upper door hinge pin and support the door, then remove the bolt from the lower hinge pin hole and remove the door from the vehicle. To install:# To install the door, position it on the hinges and insert a bolt through the lower hinge pin hole. # Using a new hinge pin clip, install the upper hinge pin. # Remove the bolt from the lower hinge pin hole. Using a new hinge pin, install it into the lower hinge pin holes. # Compress the door hinge spring and install it into the door hinge using the door hinge spring compressor tool. # If equipped with power door components, re-engage the wiring and install the trim panel or pieces, then connect the negative battery cable. ADJUSTMENTSFactory installed hinges are welded in place, so no adjustment of the system is necessary or recommended. Service replacement hinges are bolted in position and may be adjusted. If your vehicle is equipped with service replacement hinges, please refer to the door hinge adjustment procedure located later in this section. Depending on the type of door hinge you have, you wont have the clips mentioned above. If this is the case there will be a silver cap that sit on the top of the door pin. all you have to do it hit the top of the pin with a BF hammer (or rubber hammer) and a punch. The pin will come straight out. One thing to be aware of, as soon as that pin is out it will put all the pressure on the other pin. U should use a bucket and place it under the door so that it doesnt fall too much. I did mine yesterday and it took about 30 minutes. If you have the right tool (which I didnt) and someone to help you it should be no longer than 30 minutes. Good Luck!!!!!!
How can you remove the pins from a hinge on a door inside your house?
You shut the door, if needed spray each hinge with WD 40. Then take a straight screwdriver and a hammer to pound out the hinge. In an upward motion the end of the screwdriver against the bottom edge of the top of the pin, then take the hammer and pound on the end of the screwdriver to loosen. When loose you may be able to remove it with your hand or pliers. The above will not work on some door hinges such as Schlage. THIS WORKS ON SCHLAGE: Heat the hinge with your hair dryer to loosen the goop inside the hinge. Use pliers to hold the hinge as it will get very hot. Once it's hot enough, insert a small screw driver into the pin hole. Bang the screwdriver and I promise the hinge will come out. It worked for me on all my Schlage hinge pins.
How do you change the passenger side door on a 1996 ford explorer?
You first need to pull the electrical connections out from the door. You access them by taking off the interior panel from the door. Then undo the connectors. I would tag them some how just incase to ease in the installation. They need to come out back through the wire loom that goes in between the door and the body. The door will be heavy. Have a person on hand to help. To remove it all you do is remove the hinge bolts. There will be two for top hinge and two for the bottom hinge. Either remove the bolts from the door side or the body side. Whichever set is easier. It should be off. Then just change it out and re run the wire. Hope this helps. Good luck.
How do you install mirrors on a Jeep Wrangler?
They attach to the top door hinge with three screws
Where is the fuse box 1991 Lexus?
In the ES250 model, the fuses are located in 2 primary places. In the engine compartment, on the drivers side, along the top outside wall, in a black compartment. Just pop open the snap on hinge to gain access to these fuses. Secondly, inside the car, drivers side floor panel area. Remove panel door to access these fuses.
