Call an auto parts store, tell them what make/model/year car you have and ahk if they have a window-crank removal tool they can sell you. If so, ask the guy who sells it to you how to use it. Best I can do for you, best of luck.
Remove inside door handle and window crank handle, remove inside door panel, remove vent window and channel assembly, remove window.
To replace the window crank handle on the 1993 Geo Prism, first remove the interior door panel. Then, access the screw that holds the window crank in place and remove it. You can then remove the handle itself.
Remove the inside door panel. Remove the Allen screw from the window crank linkage. The window crank handles should come off.
If there is no faster head visible then it likely is attached with a clip on the backside of the crank handle. slip the handle between the handle and door panel to remove the clip.
To remove the window crank on the 1992 Toyota Paseo, first pry off the interior door panel. Then, access the screw that holds the crank in place. Remove the screw and the handle will come loose.
You can remove the window crank handle by just using a simple shop rag. How you do this you slide the rag(unfolded) between the door panel and window crank and rotate around the window crank until you snag the clip that is retain the window crank. The clip is a simple wire clip shaped like a "C" To reinstall you place the clip back in the groove on window crank and press back on the window regualtor shaft
Remove the inside door panel of your 1997 Chevy Lumina. Remove the linkage to the window crank. Remove the window crank retaining bolts. Reverse the process to install the new window crank.
You will need to remove the inside door panel of your 1977 Chevrolet blazer. Remove the window crank linkage. Remove the window crank retaining bolts. Reverse the process to install the new window crank.
Pry the screwdriver between the door panel and the window crank base. Remove the metal clip slowly and carefully. Pull the base of crank to remove it.
First remove the Window Crank Handle. Then remove all of the screws you can find, 1 for the door release, 1 for the door grip, and 4 for the door panel. Pop loose all of the lower door area, and carefullyremove the door panel. Remove the plastic behid the door panel, SAVE IT!!. With the window all of the way down, remove the screws that hold the window in and remove the window. Revers to reinstall, being sure to locate the new window into the grooves for that.
To remove the door panel on the Holden Astra, first pop off the light lens if the door has a light in the door. Then unhook the light from connector. Remove the screws holding on the armrest, door handle, and window crank if equipped.
Your local auto parts store will sell you an inexpensive tool for under $10 to remove the clip from behind the handle to release handle from door.
To install an exterior door handle on a Cherokee Jeep, first remove the window crank handle and the three screws in the inner door trim panel. Second, remove the inner door panel from the door using a trim stick and take off the vapor barrier inside the door. Third, remove the nut on the rear of the door handle, position the exterior door handle, and secure in place.
remove the door handle and window crank (you can use a coat hanger to remove the clip) remove the door lock knob. Then reach down at the bottom and pull out the panel. Install in the same order.
1. On manual window models remove the window crank handle dislodge the clip 2. Remove the outside mirror cover 3. Detach the door handle trim piece and disconnect the door pull mounting screw. Unplug the electrical connector from the power window switch 4. Remove the retaining screws and detach the panel by carefully prying it away from the door
you have to remove window crank and door handel first
You need to remove the window hand crank with a window hand crank removal tool.
Make your life easy and just break off the door handle. When you are finished with your project, just replace the door handle with a new one from the dealer.
door handle removal tool any auto part store in HELP section
You will need to remove the inside door panel. Remove the door handle retaining screws. Remove the linkage from the back of the door handle.
There is a horseshoe-shaped metal clip behind the window crank. You must ply the clip out from behind the crank in order to release the crank itself. I would advise you to remove the crank before unscrewing any parts to the door (the process can be very difficult and this will save time). Some auto stores sell cheap removal kits for this.
You need a special tool to remove it . The tool slides between the door and the handle and pushes the clip out
you must pull inner door panel, window crank and inner handle then you have two 10 mm nuts holding outer door hanle on you must remove the release rod from handle remove nuts and replace handle assemble in reverse order
Removing the Door Panel Coverings put the crank handle is in the Down Position. With either a Crank Spring Removal Tool, or a flat Screwdriver, remove the spring, located in a slot on the back of the crank.edited for clarity from this source:http://www.a1electric.com/focus.pdfAndyAnswerBTW, I tried the screwdriver ... no luck... will need to get the clasp remover... (also you may need a deep socket wrench to remove the door pull bolts from the door pull...) Good luck. AndyAnswerWindow Crank Tool Method 1. Insert Removal tool between crank handle and door, lined up with the crank handle as shown in figure 1.2. Push tool inward firmly to disengage spring clip.3. Retain Spring clip so you don't lose it.4. Remove Window Crank.Cotton Rag Method 1. Try to work the rag in between the crank and the spacer that rests against the door panel.2. Move the rag in a "dental flossing" motion see-sawing back and forth. Eventually you'll hit the right spot, and the clip will pop off.3. Retain Spring clip so you don't lose it.4. Remove Window Crank.Re-Installing the Window Crank 1. Snap the clip on the crank handle.2. Push the handle back onto the shaft.Source: http://www.focushacks.com/index.php?modid=46
you need to remove the inner door panel. Usually pop grommets but may be screwed. That will give you acess to the crank and the inner workings of the door to remove and connect a power window if needed.