I recommend using an awl for this, but a good pair of needle nose pliers will work. You'll also need a large screwdriver. First, remove the washer fluid line from the wiper. I'd use a grease pencil to mark the position of the blade on the window to made intallation easier. On the wiper arm, there is a little 'U' shaped tab, which is spring loaded and fits into the groove of the wiper motor pinion. Using the awl (or pliers), pry the tab away from the pinion, and using the screwdriver (wrap the screwdriver in a rag or something similar to prevent scratching your paint!) pry upwards on the arm. The arm itself has a strong spring on it, so you might have to lift on the wiper to help in getting it off. There might be a tool for this job, but since I'm a self-taught shade-tree mechanic, I use what's at hand! Good luck.
Its attached to the windshield wiper motor you will have to remove the cowl to get access to it.
You lift up the wiper arm and look for a clip to press at the end of the wiper arm. Slide off old wiper blade and clip on the new one. I did them both today and took less than 5 minutes.
The motors, both for the front and the rear, are located at the very bottom of the windshield wiper fluid reservoir. To gain access to them, you have to remove the battery and the battery plate, along with several other bolts that you gain access to from under the car.
Remove the windshield wiper arm from the windshield wiper motor. Remove the wiring harness. Remove the retaining nut. Reverse the process to install the new windshield wiper motor.
Drain the fluid from the reservoir. Reservoir drain tube. Remove the wiper reservoir retaining bolts. The wiper reservoir will come off.
Yes, there is a windshield wiper relay on a 1992 Chevy Lumina. The windshield wiper relay is located in the underhood fuse panel.
I've got a better question, why is this question in the Chevy venture forum ?
The 2007-2010 Chevrolet and GMC Suburban takes a special 12" rear wiper blade. (also 22" replacement windshield wiper blades on both sides front).
where is the fuse for 06 chevy cobalt windshild wiper
are you serious... life blade off windshield, unclip plastic fastener off the center of the wiper arm, remove wiper, replace in reverse order.
# Remove the windshield wiper arms # Remove the cowl cover # Disconnect the electrical connector from the wiper motor # Detach the wiper motor/linkage assembly from the cowl # Remove the wiper motor retaining bolts and remove the motor
* Remove the windshield wiper arms * Remove the cowl cover * Disconnect the electrical connectorr from the wiper motor * Detach the wiper motor/linkage assembly from the cowl * Remove the wiper motor retaining bolts and remove the motor
The 2004 Chevy Malibu windshield wiper relay switch can be found on the firewall in the engine compartment. The windshield wiper relay switch will be on the drivers side of the firewall.
# Remove the wiper arms # Remove the windshield wiper cowl cover # Disconnect the electrical connector from the wiper motor and remove the motor # Remove the wiper motor retaining bolts # Pry the linkage arm off the wiper motor pin with large screwdriver
NOTE: To prevent glass and/or paint damage, do not pry windshield wiper pivot arm from windshield wiper mounting arm and pivot shaft with metal or sharp tool. 1. Turn ignition switch to the ACC position. Turn turn signal and windshield wiper switch ON. Allow windshield wiper motor to move the windshield wiper mounting arm and pivot shafts three or four cycles, then turn off the turn signal and windshield wiper switch. This will place the windshield wiper mounting arm and pivot shafts in the park position. Turn ignition switch to the OFF position. 2. Remove the windshield wiper pivot arm and windshield wiper blade by first applying downward pressure on the windshield wiper pivot arm head, while holding the windshield wiper pivot arm. Then lift the windshield wiper pivot arm to the highest position and, using finger pressure only, grasp slide latch tab and slide latch out from under the windshield wiper pivot arm head. Remove windshield wiper pivot arm and windshield wiper blade assembly. 3. To remove the windshield wiper blade, insert a screwdriver into the slot provided at top of the windshield wiper blade frame, push down on spring lock and pull the windshield wiper blade from the windshield wiper mounting arm and pivot shaft . 4. Install the windshield wiper blade onto the new replacement windshield wiper pivot arm. See sources and related links below for replacement wiper blade information.
You have to remove the linkage from the wiper motor.
http://www.ehow.com/video_4936070_install-windshield-wiper-motor.html?pid=1&cp=1 (this is a complete video on how to remove and replace a wiper motor...very informative.)
You will have to remove the wiper arms, then remove the cowl, and then the wiper motor.
The wiper motor is located under the black plastic cowl below the windshield.
It is attached to the wiper motor.
http://www.ehow.com/video_4936070_install-windshield-wiper-motor.html?pid=1&cp=1 (this is very informative video on how to remove and replace a windshield wiper motor)
You begin to remove the windshield wiper motor by removing the cowl. Disconnect the wiper unit drain tubes and remove the mounting bolts. Replace with working unit
The 1999 Chevrolet Suburban takes 18" replacement windshield wiper blades on both sides front and a 13" rear wiper. See sources and related links below for more information.