MOTOR FOR WIPERS
Windshield wipers not working on a 1995 Nissan sentraTry the panel between the hood and the windshield. that is where the linkage is located. I have had problems where the linkage has broken. and the wiper will not work at all
The linkage for the wipers could have slipped. If the linkage is not aligned right, then the wipers will not stop at the right spot.
use a bat
the windshield wiper motor could be getting Hot! Mine does the same thing, then when it cools off they work again.
Fuse 10 (25 amp, white/clear)
Your rear windshield wiper uses the same reservoir that your front wipers use. It is under the hood on the right hand side. Good luck.
If windshield wipers are stuck in position and won't move, I would say that the windshield wiper motor needs replacing. This happened to me last year.
Try using a guitar string
Go to this website: - click on "Resources" on the left.
The GMC S-15 became the GMC Sonoma in 1991.
Hey I just went to a Japanese Car Wrecker paid $15.00 and took the entire assemblies of a 90 or 92 Honda and it works great.
Most wipers are now universal with kits to fit most cars and trucks, you just need to know the length.
NOTE: To prevent glass and/or paint damage, do not pry windshield wiper pivot arm from windshield wiper mounting arm and pivot shaft with metal or sharp tool. 1. Turn ignition switch to the ACC position. Turn turn signal and windshield wiper switch ON. Allow windshield wiper motor to move the windshield wiper mounting arm and pivot shafts three or four cycles, then turn off the turn signal and windshield wiper switch. This will place the windshield wiper mounting arm and pivot shafts in the park position. Turn ignition switch to the OFF position. 2. Remove the windshield wiper pivot arm and windshield wiper blade by first applying downward pressure on the windshield wiper pivot arm head, while holding the windshield wiper pivot arm. Then lift the windshield wiper pivot arm to the highest position and, using finger pressure only, grasp slide latch tab and slide latch out from under the windshield wiper pivot arm head. Remove windshield wiper pivot arm and windshield wiper blade assembly. 3. To remove the windshield wiper blade, insert a screwdriver into the slot provided at top of the windshield wiper blade frame, push down on spring lock and pull the windshield wiper blade from the windshield wiper mounting arm and pivot shaft . 4. Install the windshield wiper blade onto the new replacement windshield wiper pivot arm. See sources and related links below for replacement wiper blade information.
in the fuel tank
Did you look in your fuse panel, or on the back of the cover to fidn one marked wipers? If it has electrical current going to it, then there has to be a fuse or a fusable link in the wiring system.
Just to bug the crap out of you. That is just the way they are. My 95 is the same. Just think happy thoughts when you look out of the windshield. Eventually you wont even notice them any more. Answer, I also have a wrangler 1991 that does that too. It stopped at the bottom to the windshield, until i replaced the windshield. then it started stopping up about 1/3 of the way. I believe that whatever tells the windshield wiper to stop got misaligned, but im too lazy to fix it.
The 1991-1999 Toyota Tercel takes 18" replacement windshield wiper blades on both sides front. Be sure to always lookup the exact part numbers for the brand of wipers you decide to purchase. This not only ensures the correct lengths but also the correct attachments. See related links below.
passanger side under the dash
The 1991 Acura Integra takes a 20" drivers side, 19" passenger side and a 16" rear wipers. See sources and related links below for more information. Since there are over 22 different wiper arm attachments, do not buy wipers just by length only. Be sure to lookup exact wiper blade part numbers by vehicle make, model and year for the brand wiper you decide to purchase. This ensures correct length AND correct attachment.
It is possible that your wiper switch is bad. The switch can be cleaned with an aerosol switch cleaner if that does not work then replace it. Pls let me know how it goes Regards Ehi
typically 4.5 quarts