Cadillac STS

How do you replace 93 Cadillac sts trunk light bar?

567

Top Answer
User Avatar
Wiki User
Answered
2012-05-10 16:39:57
2012-05-10 16:39:57

you cannot replace the individual bulbs- they are meant to last the lifetime of the car. best solution is to get a completely new trunk...

001
๐Ÿ˜‚
0
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Related Questions



no the bar light on your instrument panel that is located on the trunk of the car diagram would light.


It may be due to a bad alternator. If the alternator has a bad diode it will draw battery power when the car is off. Another possible draw is the trunk light. The trunk light works with a sensor that is mounted to the curved bar on the left side (drivers side) of the trunk. This sensor sometimes slides out of adjustment and keeps the trunk light on when the trunk is closed.


The Cadillac Bar is located in Houston, Texas more specifically, 1802 Shepherd, TX, 77007. There is also a secondary location of the Cadillac Bar at the Kemad Boardwalk, in Kemah, Texas, 77565.


Depending if it is the "marker" or brake light, start by opening the trunk lid. Turn yourself upside down and backwards to see the inside of the lip on the trunk lid. You will see 7 black ABS plastic knobs. Take them off and the entire rear tail light bar will come off. You can then unplug each light bulb by screwing out the sockets (1/3 turn) from the light assembly. I am doing it myself this morning!


To reset the Check Engine Light you must go to the trunk of your car get a cro-bar and smash the dash board until the light doesn't come on no more...


There's three slots on the sides of the trunk tensioner bar, you adjust the tension by moving the bar in the different notches.


No, a stop bar and a whammy bar are two different things therefore you cannot replace a stop bar with a whammy bar. It woluld make the sound a whole different tune.


Cadillac Jack's Sports Bar is located in the state of Ohio. Cadillac Jack's currently has three locations which include Centerville, Fairborn and Beavercreek.


no back seat. just row bar and open trunk. Two seater and a trunk behind a rocket ship



ANSWER:There are two fuses that power this system:A 40 amp Maxi fuse in the under-hood fuse panel.A 15 amp fuse in the under-dash fuse panel.Are you sure you checked both?Is there a "Trunk Ajar" light on the dash?From there, check that you're getting power to the pull-down motor at two points:1. The Orange wire2. The Dark Green wireThe Black/yellow wire is the ground feed that goes to the latch switch. It provides the ground for the pull-down motor, so see if it is providing a ground. If so, the motor itself is suspect and should be checked for binding etc. prior to replacing.If you don't have the funds to replace the motor pulley, simply consider the following:Simply tap the silver bar located on the motor's left side downward into it's pulled down ending place. Having done this, your trunk will lock and close and protect things in your trunk as well as theft of your car. Just keep tapping with a gentle hammer hit until the trunk closes. Your electric trunk open will still function (if it is already functioning) and the water/snow will stay outside where it belongs. Replace motor later. It's about $40 US dollars as I recall.I found that the hammer technique did not work, so I opened the motor to gain access to the rotor and turned the rotor manually to adjust the position of the silver bar. Doing this put the trunk light switch out of commission, so I removed the trunk light and now keep a flashlight there. Put the rotor back in its housing and reattach housing, so that manually adjusted position of the silver bar is retained.I did everything that they said in this answer, but nothing happened. What i did to make it work was to make sure the switch on both the motor (next to the silver latch) and the trunk lid (i small black switch in the housing).


Remove the two screws holding the rear assembly in place, you must open the tailgate to see them. Pull on the assembly and it will come out of the mounting pins. Place on cloth of some sort to not scratch the lens, remove all the screws holding the light bar on the back side of the lens and remove the bar. You can then replace the bulb(s)


form_title=Install a Truck Light Bar form_header=Add extra illumination to your vehicle. Would you like a truck light bar with a reverse backup light function?= () Yes () No Would you like turn signal functions with your truck light bar?= () Yes () No Is there a particular color you'd like your truck light bar to be?= () Yes () No


Holland Island Bar Light ended in 1960.


Holland Island Bar Light was created in 1889.



well ur battery is located in the trunk on the right side there is 2 plastic type of screws after unscrewing them pull out the whole panel there will be ur battery just release the little bar holding the battery then remove the battery and replace it



For a 1994 Deville it is at the back of the engine. Difficult to get at. Must remove the cross bar and air horn, move the wireing adjacent to the motor. Expect to take 2-3 hours.


busbar - a bus with a bar on it busbar trunking system - a bus with a bar which has a trunk attached to it.


First make sure your trunk is clear of obstructions and the capacity shield that limits the height of things in your trunk is in place. As you know the shield works to allow for the roof mechanism to have room in the trunk to work. Without this shield in place you can get some strange reactions from the roof mechanisms including activating the roll bars.


how do you replace the front sway bar likn in a 1999 Grand Marquis?



The 2001 Honda Accord uses a 3057 bulb in both taillight assemblies as well as the light bar on the trunk lid. When a bulb burns out, replace it as soon as possible to maintain your visibility on the road. Working taillights are required by vehicle safety regulations in most states. You can buy the bulbs from an auto parts retailer and change them at home in minutes. # Step 1 Open the trunk of your Honda Accord. Locate the plastic screw fastener on the inside of the trunk wall. Insert a coin into the fastener and turn it counterclockwise to remove it. Pull back the trunk lining to expose the taillight assembly. # Step 2 Twist the upper bulb 1/4-turn counterclockwise then pull it back out of the socket in the Accord's taillight assembly. Insert the new bulb into the socket, pushing it all the way in until it stops. # Step 3 Insert the light into the Accord's taillight assembly and turn it 1/4-turn clockwise to lock it in place. Replace the trunk lining. Push the fastener into place until it clicks. # Step 4 Repeat the process on the Accord's second taillight. Close the trunk and test the taillights. Trunk Lights # Step 1 Open the trunk of your Accord. Locate the trunk-mounted taillight bulb inside the trunk lid. # Step 2 Grasp the bulb on the driver side and turn it 1/4-turn counterclockwise. Pull the bulb out of the light assembly. # Step 3 Pull the bulb from the socket. Insert the new bulb straight into the socket until it stops. Insert the bulb into the light assembly and turn it clockwise until it locks. Close the trunk and test the lights.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.