0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How much does it cost to replace a peugeot 206 drivers side door?
Between £25 and £70 for a door from a scrapyard or ebay and an hour or two of your time.
How do you fix leaking windows - top corners of a 1988 RX7 Convertible?
Replace the convertible door seal.
How do you replace door seal in 2000 Integra?
i would think you would get a new door sealer or if its a part you need look it up on http://eBay.com/ or you could probobly find door sealer at any machaincs store
How replaced transmission seal my Tahoe?
Front seal: remove engine or transmission and replace the seal. Rear seal, remove the drive shaft to replace the seal. Unfortunately, you typically only have problems with the front seal.
How do you replace a rear wheel bearing and seal on a 98 Toyota Tercel?
how do i replace a wheel seal
Door weatherstripping on 2002 Volvo S80?
If you want to install door weatherstriiping on 2002 Volvo S80 you should try to follow this steps: Open the car door and inspect the existing door seal. Begin at one end and pinch the seal with your fingers and pull up. Find the anchor points for the old door seal and determine if it is glued or clipped or if screw fasteners hold it to the door frame. Use a razor to cut the seal away from the frame for glued applications, unscrew the fasteners for screw anchors or pull up on the seal with pliers where it clips into existing drilled holes in the door frame. Clean the door frame where the old door seal was attached. Clips that hold the new seal should be sanded lightly with Emery cloth. Door seals that use push clips should have holes that are clear of debris. Use a drill and bit to clean these holes. Clean the door frame down to the metal where the old door seal was laid if the old seal was glued to the frame. Stretch the new door seal around the door frame for a proper measurement. If the new door seal has push pins or slides that need to be mated with the holes or slides on the car door frame, then you must adjust the position of the new seal to match the anchor points on the frame. For glue-type door seals, you just need to cut and measure to the correct length. Secure the new car door seal to the car door frame. If you are screwing the new seal in place, use the existing anchor points to fasten the door seal to the door. For a seal using fasteners, push the new fasteners into the existing holes. Glued seals will require you to spread an even layer of glued along the outside of the door frame and then center the seal and press firmly to affix the door seal to the frame. Glue should be allowed to dry at least six hours before closing the door, preferably 24.
How much does it cost to replace a peugeot 206 cambelt 2002?
I paid £180 for one to be replaced on a 2001 206
How do I install a outer door seal or weather strip for a Jeep wrangler half door that has more clips than the corresponding holes than they are suppose to push into?
If the new door seal has more clips than is necessary to install it on a Jeep Wrangler, the seal can be trimmed with a scissors to fit the door. Another way to remedy this is to return the door strip to the store where purchased and get the smaller, half door seal.
How do you replace the side manual mirror on a Monte Carlo?
You have to remove the door panel from the inside of the door. Break through the plastic seal and you will see two nuts holdong the mirror on - remove them - mirror will fall out. Before putting the interior door panel back on, tape the plastic seal back shut. If you don't, you will feel air coming in around the door handle when driving - very cold in the winter.
How do replace a peugeot 206 car aerial?
cant be replaced
How to replace the Front axle seal on a Ford Escape?
how do you replace left front seal on 2009 ford escape
How do you replace a Ford F-150 rear axle seal?
how do you replace a Ford F150 rear axle seal
