answersLogoWhite

0

  • Car Computers and Sensors
  • Chevy Impala
  • Chrysler Sebring

How do you replace a body control module for a 1999 Chrysler Sebring convertible?

User Avatar

Wiki User

βˆ™ 2008-04-28 14:41:19

Best Answer
Copy

The bcm is attached to the fuse box. You will have to remove the dash by taking out the screws around the radio and on the left side of the dash. You'll have to remove the dash silencer (above the driver's legs) as well. Unplug everything from the fuse box, then remove the three screws holding the fuse box in place. Pull the fuse box straight down to remove it. Unplug the bcm from the fuse box and remove the screws holding them together. Now you've got your part number and can look for a new bcm. (I had a hard time figuring out how to do this when the gauges in my '99 Sebring convertible quit working. It's pretty easy to remove and saves a lot of money when you don't have to take your car to a dealer. Good luck!)

2008-04-28 14:41:19
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Your Answer

Loading...
Still have questions?
imp

Related Questions

When to replace the Timing belt in a 1997 Chrysler Sebring convertible jxi?

100,000 miles


DO you have to drop the fuel tank on a 1999 Chrysler Sebring convertible to replace the fuel pump?

Yes


When should you replace the timing belt on a 1999 Chrysler Sebring JXi Convertible?

100,000 miles


How do you replace windshield washer pump Chrysler sebring convertible?

The windshield washer pump on a Chrysler Sebring convertible is replaced by disconnecting the wiring harness and unbolting the pump. It can then be lifted from its mounting bracket and a new pump put into place.


How do you replace the alternator in a 2000 Chrysler Sebring convertible?

When replacing the alternator on a 2000 Chrysler Sebring convertible begin by removing the belt. Next, remove the wiring. Lastly, remove the retaining bolts. Reverse the process to install the new alternator.


Can you replace a 2.7L engine in a 2002 Chrysler Sebring convertible with a 3.0L from a same year Chrysler Sebring coupe?

It is not a direct swap. They use different transmissions, computers, wiring, etc.


How long should labor take to replace a water pump in a 1996 Chrysler Sebring Convertible?

6 hours


How do you replace the starter on a 2001 Chrysler Sebring convertible?

Remove the positive battery cable from your 2001 Chrysler Sebring battery. Remove the cables from the starter. Remove the starter retaining bolts. Reverse the process to install the new starter.


How do you replace a Chrysler Sebring 2001 Cabin Filter?

A 2001 Chrysler Sebring does not have a cabin filter.


Will a home link visor work to replace a regular visor in 1998 Chrysler Sebring convertible?

It will bolt up, but I do not think you will have the power electrical connector.


DO you have to drop the fuel tank on a 1998 Chrysler Sebring convertible to replace the fuel pump?

Yes. The fuel tank must be removed to access the pump.


Chrysler sebring ignition damage by thief key doesn't work how do you replace?

Chrysler sebring ignition damage by thief key doesn't work how do you replace?"


How do you replace the convertible top motor on a 2000 Chrysler Sebring jxi?

It is located behind the rear seats. Once you remove them you will see the pumps and lines. There are several youtube vids on how to remove and replace it.


Can you replace an 2.7 Chrysler engine in a 2006 sebring with an 3.2?

No, the 3.2L will not fit a Sebring.


How do you replace the transmission solenoid pack on a 1998 Chrysler Sebring Convertible?

To replace the transmission solenoid pack on a 1998 Chrysler Sebring, remove the air filter box, the battery, and the battery tray. Remove the 4 bolts on the frame and the trans cooler lines. The solenoid pack is screwed to the to the transmission with 3 10 mm bolts. Remove the solenoid pack and replace it.?æ


How to replace push rods on a 2002 Chrysler sebring gtc?

A 2002 Chrysler Sebring has an overhead cam engine. That means it does not have push rods.


Can I use 21560R16 or 22560R16 tires to replace the stock 20560R16 tires that came on my 2004 Chrysler Sebring Convertible?

I just put Michelin P215 60 HR 16 Primacy MXV4 tires on our 2004 Sebring Convertible GTC with stock wheels. Car drives and handles much better.


How do you replace the windshield on a 1996 Chrysler Sebring convertible?

Replacing a windshield on a modern car is not a DIY job, besides, a broken windshields are covered by your insurance with no deductible. Call a Automobile glass replacement service and have them replace it.


What does it cost to replace crankshaft sensor on Chrysler sebring 1999?

60.00 $


How much should it cost to replace the rack and pinion on a 1996 Chrysler Sebring?

It will cost between $300.00 to $500.00 to replace the rack and pinion on a 1996 Chrysler Sebring. This cost includes labor and parts.


What does it cost to replace a carburetor on a 2004 Chrysler Sebring?

It would be very expensive considering that car doesn't have a carburetor.


How much should it cost to replace a blown head gasket on a Chrysler sebring V6?

The price to replace a blown head gasket on a Chrysler Sebring V6 should be around $1,000.00. The price can vary depending on where you have the repairs made or if you replace it yourself.


How do you replace the fuel pump in a 1999 Chrysler Sebring?

Drop the fuel tank


How do you repair a harmonic balancer for a 2001 Chrysler sebring?

You dont repair it...you have to replace it.


When should you replace the timing belt on a 2003 Chrysler Sebring?

100,000 miles