0
How do you replace a ground fault interrupt outlet with a regular one?
Wiki User
∙ 14y ago
- I would NOT do that if I were you. If someone is electrocuted and local, county or state officials discover that the GFCI has been removed, you could have some serious problems in court.
- If a GFCI was installed, there was a good reason for it; electricians don't put one in unless it is required by code.
- If you INSIST on replacing the GFCI, connect the white wire that screws into the GFCI to the neutral bar in the breaker panel and disconnect the white pigtail that comes out of the GFCI, then connect the BLACK wire to the new breaker.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What do you need and how can you install a ground cable if your 240V outlet doesn't have a ground wire?
You need a 3 conductor wire with ground. For example if you had a 30 amp breaker for that outlet you would need 10awg 3w/ground. That's 10 gauge 3 conductor with ground and replace the old wire back to the panel.
Can you replace a 2 prong outlet with a 3 prong outlet if there is no ground line or is the ground required?
YES - it will work fine, and hopefully you have grounding in the plug. If you do not, you should also get surge protection and a safety cap when not using. The 3 prong will not create a ground, so it will not change the fact that it is dangerous not to have ground (you know kids and outlets).
What is a 3 prong outlet?
Simply put, it is any electrical outlet the has three holes that the female end plugs into. What this is referred to most of the time (but not always) is a regular 110V outlet. Older outlets had only two holes, one for the hot, one for the neutral. All newer installations have the third hole for the ground wire.
Wiring single toggle switch and outlet with two wire system?
Guessing you are replaceing an outlet? Black goes on the copper colored terminal and white on the same side that has the ground terminal. If you have checked and made sure that white is in fact the neutral you can run a jump wire from the side terminal to the ground. This will ground whatever you plug into the outlet as long as it has a 3 prong plug.
Can you properly change a 3-prong 240V outlet looks like standard plug but horizontal to the NEMA twistlock 20A style if they use a different number of wires extra ground neutral on a twistlock type?
No. You can't replace a 220V outlet with a 110/220V outlet without running the requisite neutral wire. If you do you will blow out any device that expects the neutral line to be connected.
What do you need and how can you install a ground cable if your 240V outlet doesn't have a ground wire?
You need a 3 conductor wire with ground. For example if you had a 30 amp breaker for that outlet you would need 10awg 3w/ground. That's 10 gauge 3 conductor with ground and replace the old wire back to the panel.
Can you replace a 2 prong outlet with a 3 prong outlet if there is no ground line or is the ground required?
YES - it will work fine, and hopefully you have grounding in the plug. If you do not, you should also get surge protection and a safety cap when not using. The 3 prong will not create a ground, so it will not change the fact that it is dangerous not to have ground (you know kids and outlets).
Why does a newly installed GFCI outlet show open ground on the tester?
Ground wire is loose or disconnected somewhere in that circuit.
How can you wire a 110V plug outlet from a 240V plug outlet not speaking of a converter but actually changing the plug outlet so that there are no long term effects on the 120V appliance?
Assuming the wiring to the outlet has 2 loads and one neutral, isolate one load from the outlet and use the neutral as the common. be sure to ground from the receptacle to your conduit or ground lead. You should also replace the corresponding breaker with a 120 volt single breaker.
Is the switched portion of an outlet mounted toward the top or the bottom?
There is no switch on an outlet. You can mount an outlet with the ground up or down. Most electricians I know mount the ground down as I do.
When wiring a range the outlet has a neutral ground and 2 hots you have three wires do you put the bare wire in the neutral or ground on the outlet?
the bare copper is always a ground
When should you use an ungrounded outlet?
If the wiring system into which you are installing an outlet has no ground available, use an ungrounded outlet. In an ungrounded system, an outlet with a ground contact would allow the outlet user to mistakenly, and perhaps dangerously, assume that a ground was present. A suitable ground may be available as a ground wire accompanying the hot and neutral wires in the cable, or a ground may be available via conductive conduit and a metal outlet box. In any case, use a tester to confirm the integrity of the assumed ground. A voltage test from the hot wire to the ground should show the same voltage as between hot and neutral (the black and white wires respectively). If you are replacing an ungrounded outlet, you need not assume there is no ground present. You may find, in the box, ground wires that were not connected to the outlet. You may come across grounded outlets that have no ground wire attached because they rely on grounding via the mounting screws through the outlet ears to the metal box. This is a less reliable grounding method. It is better to buy a ground-wire "pigtail," fasten the wire directly to a hole in the metal box with the supplied screw, and attach the other end of the ground wire to the outlet via the outlet's ground screw.
Is a ground fault indicator outlet installed at the breaker box?
There are tow places to put a Ground Fault Circuit Interrupter. There is a GFCI breaker which would be installed in a breaker box and a GFCI outlet that can be installed anywhere. Most GFCI outlets allow you to connect regular outlets to the GFCI and those outlets will also be protected.
What is a 3 prong outlet?
Simply put, it is any electrical outlet the has three holes that the female end plugs into. What this is referred to most of the time (but not always) is a regular 110V outlet. Older outlets had only two holes, one for the hot, one for the neutral. All newer installations have the third hole for the ground wire.
Why do outlets have two prongs?
Actually they have 3. A round ground, wide neutral, and narrow hot. If it only has 2 it is an old outlet with no ground wire. If that is the case in your home, I highly suggest you connect a jumper wire from the ground screw to the white neutral wire on the silver screw to provide some protection. Do this at every outlet in the home. Replace all the outlets in your home with new ones if they are so old they do not have a ground connection.
How do you check your wall outlet for ground?
You can get a tester that plugs into the outlet at any home improvement store.
What type of outlet is needed to supply electricity to a spray tan machine?
A spray tan machine needs an outlet with a ground so that electrocution does not occur. The outlet must supply at least 110 volts. A standard outlet with a ground installed should suffice.
