0
Remove the upper radiator hose, carburetor, intake manifold, and exhaust manifold. There are lots of hoses and wires going to various devices on the intake manifold and around the engine that have to be removed also. Additionally the alternator, water pump, smog pump, etc. need to be removed.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
Pontiac Sunfire 2001?
A 2001 Pontiac Sunfire has 115 HP to 150 HP. The average miles per gallon for gas is 23 city and 32 highway.
How much is a intake gasket for a Nissan maxim?
I just replaced mine today. I have a 99 maxima 3.0 The gasket was $23 at Pep Boys.
What should the fuel pressure be on a 2003 Pontiac sunfire?
At idle: 13-20 psi Key on engine off: 23-31 psi
What are the release dates for Over Your Head - 2006 2010-10-23?
Over Your Head - 2006 2010-10-23 was released on: USA: 23 October 2010
How do you remove cylinder head from 1989 Camry 4-cylinder?
This is the procedure for valve cover, not cylinder head removal, please improve!!C-LTC and 2CL-TC EnginesSee Figures 1 and 2Disconnect the negative battery cable. Remove and label all electrical wiring, connectors and vacuum hoses necessary to gain removal clearance.Fig. 1: Loosen and remove the cylinder head cover retaining nutsDisconnect the PCV hose.Remove the six nuts and seal washers from the cylinder head cover. Loosen them in a crisscross pattern.Remove the cylinder head cover and the cover gasket from the cylinder head. Discard the gasket and replace with a new one.To install: With a wire brush or gasket scraper, remove all the old gasket material from the cylinder head and the cylinder head cover gasket surfaces.When the cylinder head surfaces are free and clean, apply beads of sealant to the cylinder head in the locations shown in the accompanying illustration.Fig. 2: Be sure to apply sealant on the cylinder head prior to cover installationInstall the new gasket in the cover. Make sure that the gasket seats evenly.Place the cover with the gasket onto the cylinder head.Install the six nuts and seal washers. Tighten the nuts to 65 inch lbs. (8 Nm).Connect the PCV hose. Connect all removed vacuum hoses, connectors and electrical wiring. Connect the negative battery cable.Start the engine and inspect for oil leaks. Repair any leaks as necessary.2S-ELC, 3S-FE and 5S-FE EnginesSee Figures 3, 4 and 5It is recommended when replacing the valve cover gasket you replace the seal nuts also. They may be reused only if they do not seem to be damaged.Remove and label all electrical wiring, connectors and vacuum hoses necessary to gain removal clearance.Remove the spark plug wires. Disconnect the PCV hose.Remove the four nuts and grommets located on top of the cylinder head cover.Fig. 3: When removing the old grommets from the valve cover, keep them in order of removal-3S-FE and 5S-FE enginesOn 3S-FE engines, label or arrange the grommets so that they may be reinstalled in the same order. This will minimize the possibility of oil leakage when the cylinder head cover is reinstalled.Remove the cylinder head cover and the cover gasket from the cylinder head. Discard the gasket and replace with a new one.To install: With a wire brush or gasket scraper, remove all the old gasket material from the cylinder head and the cylinder head cover gasket surfaces.Fig. 4: Before installing the valve cover, apply sealant to the head in these locations-3S-FE engineWhen the cylinder head surfaces are free and clean, apply beads of sealant to the cylinder head in the locations shown in the accompanying illustrations.Install the new cylinder head gasket in the cover. Make sure that the gasket seats evenly.Place the cylinder head cover with the gasket onto the cylinder head.Install the four grommets and nuts. Uniformly tighten the nuts in several passes to 13 ft. lbs. (18 Nm) on the 2S-ELC; 17 ft. lbs. (23 Nm) on the 3S-FE and 5S-FE.On 3S-FE engines, align the grommets as shown in the accompanying illustration to ensure proper sealing of the cylinder head cover.Fig. 5: Align the grommets on the cover as shown-3S-FE engine shownConnect the PCV hose. Connect all removed vacuum hoses, connectors and electrical wiring. Connect the negative battery cable.Start the engine and inspect for oil leaks. Repair any leaks as necessary.2VZ-FE and 3VZ-FE EnginesSee Figure 6It is recommended when replacing the valve cover gasket you replace the seal nuts also. They may be reused only if they do not seem to be damaged.Turn the ignition key to the OFF position. Disconnect the negative battery cable. Wait at least 90 seconds from the time the negative battery was disconnected to start work.Remove and label all electrical wiring, connectors and vacuum hoses necessary to gain removal clearance.On the 3VZ-FE, remove the V-bank cover.Remove the spark plug wires. Disconnect the PCV hose.Remove the six (2VZ-FE) or eight (3VZ-FE) nuts and seal washers located on top of the cylinder head cover.Remove the cylinder head cover and the cover gasket from the cylinder head. Discard the gasket and replace with a new one.To install: With a wire brush or gasket scraper, remove all the old gasket material from the cylinder head and the cylinder head cover gasket surfaces.When the cylinder head surfaces are free and clean, apply beads of sealant to the cylinder head in the locations shown in the accompanying illustrations.Fig. 6: Apply sealant in these locations prior to cover installationInstall the new cylinder head gasket in the cover. Make sure that the gasket seats evenly.Place the cylinder head cover with the gasket onto the cylinder head.Install the six/eight nuts and seal washers. Uniformly tighten the nuts in several passes to 52 inch lbs. (6 Nm).Install the spark plug wires. On the 3VZ-FE, install the V-bank cover.Connect the PCV hose. Attach all removed vacuum hoses, connectors and electrical wiring. Connect the negative battery cable.Start the engine and inspect for oil leaks. Repair any leaks as necessary.1MZ-FE Engine Drain and recycle the engine coolant.Disconnect the radiator inlet hose.Disconnect the throttle and accelerator cables.Remove the air cleaner cap assembly.Remove the V-bank cover. Use a 5mm hexagon wrench to loosen the nuts.Label and remove all emission control valve hoses. Disconnect any wiring interfering with the valve cover removal.Remove the air intake chamber. This will gain you access to the back valve cover.Dsiconnect the engine wire from the left hand side, No. 3 timing belt cover, rear side and right hand side. Most of the wiring is secured by nuts and or bolts to the body of the vehicle.Remove the ignition coils, make sure the place them in order on a table so not to mix them up.Remove the 8 bolts retaining the valve covers and gasket.See Figures 7 thru 11Fig. 7: To remove the valve cover, remove the bolts and set them aside ...Fig. 8: ... then remove the cover from the cylinder headFig. 9: Inspect the seals in the top of the valve cover and replace if necessaryFig. 10: Remove the gasket from the edge of the cover and discardTo install: Clean the mating area of the valve cover and cylinder heads well. If necessary, scrape any left gasket from either surface.Apply seal packing to the cylinder heads and place new gaskets into position.Fig. 11: Inspect the cylinder head end seals. Replace with new packing material if necessaryAttach the valve covers. Uniformly tighten the bolts in several passes to 69 inch lbs. (8 Nm).Install the spark plugs in their proper locations, then place the ignition coils into place and secure.Attach all engine wiring be sure to secure each harness properly.Install the air intake chamber. Refer to Fuel System .Attach all emission hoses and wiring.Attach the V-bank cover.this is the wrong answer for the question asked, please improve!
What is the answer to Lion's Head cap puzzle number 23?
Head over heals in love
Was Isaac a teenager when the apple fell on his head?
he was 23
How many bones are inside your head?
23 bones
When was Gordon Head born?
Gordon Head was born on January 23, 1899, in Redding, California, USA.
What are the release dates for Animal Atlas - 2004 Head Cases 8-23?
Animal Atlas - 2004 Head Cases 8-23 was released on: USA: 25 June 2012
What are the release dates for The Detective's Head - 1916?
The Detective's Head - 1916 was released on: USA: 23 November 1916
What are the release dates for Scooter Head - 2002?
Scooter Head - 2002 was released on: USA: 23 June 2002
