answersLogoWhite

0


Best Answer
Copy
New for the Chevrolet Astro/GMC SafariI just did this on a 1992 Astro EXT cargo van having the Z-code 4.3-liter V6 and automatic transmission; I previously performed this operation on a 1994 Starcraft Conversion Astro (EXT) having the W-code 4.3-liter V6 and automatic transmission.

On all the Astro/Safari vans I've seen, the alternator is located on the passenger side of the engine.

Recommended tools:

  1. 8mm box-end wrench or socket (not all will need)
  2. 10mm DEEP box-end wrench or socket
  3. 13mm box-end wrench or socket
  4. 14mm DEEP box-end wrench or socket
  5. 15mm box-end wrench or socket
  6. 3-inch socket extension
  7. 3/8-inch-drive ratchet
  8. steel "butter knife" or suitable substitute
  9. teflon tape or other "thread sealer"

If you elect to use a 1/4-inch-drive ratchet in lieu of the 3/8-inch-drive ratchet, limit its use to 10mm-or-smaller sockets: the threaded fasteners in this application having larger heads require greater torque than can be safely and reliably applied using 1/4-inch-drive hardware.

Read this entire procedure first, then decide whether this is a project for you to attempt.

There are significant minor differences to the specific procedures involved, to wit:

(1) Always observe all applicable safety procedures.

(2) Disconnect the cable from the positive (+) battery terminal. For some vans, you will need an 8mm socket or wrench; for others, you will need a 10mm socket or wrench.

(3) The Power Steering reservoir is in the way on vans having the Z-code engine: leaving the hoses attached and avoiding tipping of the reservoir, remove and save the screws that hold the reservoir to the cowl; then bend the hoses and rest the reservoir on the driver's side of the radiator shroud.

The air filter box is in the way on vans having the W-code engine. Open the clamps that seal the box, remove the filter: the nuts and bolts holding the airbox in place are visible. Remove the airbox, saving the hardware.

(4) The ductwork supplying the engine with fresh air is in the way. Usually, these plastic pieces just click together, but there may be one or more clamps, nuts and/or bolts, or screws holding some of it in place. The offending portion consists of the following pieces:

(a) the lower part that turns the air about 90-degrees, so that the air flows upwards,

(b) the upright section that channels the air upwards (it looks like an Accordion's bellows on the Z-code engine),

(c) the upper ductwork connecting the upright section with the air filter housing.

I have heard that some ductwork installations are secured using #2 Phillips threaded fasteners (screws); if yours is such an application, you will also need a #2 Phillips screwdriver.

(5) Remove serpentine belt. The ratcheting tool that looks like a long, flat handle -- it came with the vehicle as part of the lug wrench kit -- has an opening that fits the pulley on the tensioner. Using the tool, loosen the tensioner with one hand and slip the belt off using the other hand.

At this point, whether you need to remove the fan from the front of the engine should be obvious. If you must, be aware that so doing without removing the shroud really isn't going to give you much room (about 1/2 an inch, maybe an inch).

If you need more than that, the shroud has to come off so that you can remove the fan. Although at 13.5 inches (34.3mm) circumference and 14.5 inches (37.9mm) circumference respectively, my forearms and upper arms are rather small, I think that needing to remove the fan to have enough room is a highly unlikely condition.

(6) Remove the engine oil dipstick bracket from the stud holding the alternator to the bracket. The nut securing the dipstick bracket is probably a 10mm. Remove the dipstick bracket from the stud. Be aware the dipstick tube could slide from the engine.

(7) The alternator bracket should be loosened from the front of the engine. Remove the bolts (it should be a trio of 14mm bolts) and save them. This allows the bracket, tensioner and alternator to be tilted away from the engine. At least one bolt may be wet with engine coolant; seal the threads of any such bolt before reinstalling it.

(8) Use an appropriate tool to unclip the plug from the alternator (I used a "butter knife), and remove the red wire from the lug at the back of the alternator. The nut securing the red wire to the alternator is probably a 10mm; the stud in the alternator is probably a 15mm (menitoned just in case the new one needs snugging).

(9) Remove the bolt from the rear of the old alternator holding it to the bracket (either a 13mm or a 14mm); then remove the stud holding the old alternator to the bracket (either a 13mm or a 14mm); then remove the "hinge" bolt holding the old alternator to the bracket (either a 13mm or a 14mm bolt screwed into a 15mm nut).

Installation of the new unit is done by reversing the steps of disassembly.

SAFETY NOTES: Be aware that there can exist pinch hazards during this procedure. Also be aware of the possible hazard of falling tools and/or debris.

Helpful hint: if possible, have someone else hold the bracket/alternator/tensioner assembly in-place while you start the lower 14mm bolt by hand from underneath the passenger side. This makes installing the upper bolts much easier.

Start ALL the bolts before tightening any of them. Generally, it goes pretty quickly if you begin with the "all bolts finger-tight, then all bolts hand (wrench/socket) tight, then all bolts torqued" method.

NOTE: Conspicuously dexterous people may not have to remove the alternator bracket, but in my opinion, the procedure is much easier if this is done. You should never have to remove the doghouse (engine cover inside the van) to replace the alternator. If a mechanic told you he/she did it that way, you should be going to a different mechanic.

User Avatar

Wiki User

โˆ™ 2015-07-15 20:51:22
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace the alternator on a Chevy Astro?
Write your answer...
Submit

Related Questions

How long will it take to replace the alternator on Chevy astro?

about 30 min to 1 hour .hope it helps


How do you change the alternator on a 1994 Chevy Astro van 4.3l?

Remove the belt from your 1994 Chevy Astro Van 4.3 liter engine alternator. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install the new alternator.


Where is the fuse that is between the alternator and the battery on a 1999 Chevy Astro?

Generally there is NO fuse between the alternator and battery.


Vacuum diagram for a Chevy Astro van?

can I get a diagram to replace vacuum hoses ona 986 chevy astro van


How do you replace driver side window in 1993 Chevy astro van?

How do i change the window on a 95 chevy astro van


How do you install a center link on Chevy Astro van 94?

how to replace a center link on Chevy astro van 1994 suspension


Where is the voltage regulator on a 1997 Chevy astro minivan?

The voltage regulator is built into the alternator.


What replace the Chevy astro van?

Nothing, it's discontinued.


Where is the voltage regulator located in 1993 Chevy astro van located?

Inside the alternator itself


Where is he voltage regulator located on a 2002 Chevy Tahoe?

It is built into the alternator, You will have to replace the alternator.


How do you replace the alternator on a 2004 Chevy Cavalier?

Remove the belt from your 2004 Chevy Cavalier alternator. Remove the alternator wiring harness. Remove the alternator retaining bolts. Reverse the process to install your new alternator.


Can you replace a 1993 Chevy astro van tranny with a tranny from a 1987 astro van?

figuratively yes but unadvisable


How do you change the voltage regulator on a 1998 Chevy astro van?

The 1998 Chevrolet Astro Van voltage regulator is part of the alternator. The voltage regulator cannot be individually changed. You will need to change the entire alternator.


How do you replace an alternator in 2003 a Chevy Cavalier?

Begin by removing the 2003 Chevy Cavalier alternator belt. Remove the wiring from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install your new alternator.


How do you replace alternator 2002 Chevy Cavalier?

Remove the belt from your 2002 Chevy Cavalier alternator. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install your new alternator.


How to replace alternator in 1993 Chevy G20?

Remove the belt from your 1993 Chevy G 20 alternator. Remove the alternator wiring harness. Remove the retaining bolts from the alternator. Reverse the process to install the new alternator.


How do you replace a fuel pump on an 89 Chevy astro van?

the pump is in side the fule tank drop tank replace pump get a astro van manual


How do you replace the alternator on a 1989 Chevy Corsica?

Begin by removing the alternator belt on your 1989 Chevy Corsica. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install the new alternator.


Where is the voltage regulator on 1985 Chevy truck?

It is built into the alternator It is all 1 unit. Replace alternator.


Does the 1999 Chevy Astro van have a voltage regulator?

I believe it is integral to the alternator... i.e. if the voltage regulator dies you need to buy a new alternator


Steps on how to replace the alternator of 2002 3.1 Chevy Malibu?

where is the location of tensioner of 2002 3.1 L Chevy Malibu to adjust if replacing the alternator?


How much to replace alternator in 2004 Chevy Colorado?

Go found out


How long does it take to replace an alternator on Chevy Trailblazer?

It should only take about an hour at the most to change the alternator.


Chevy Astro van idles rough at stop light?

replace timing chain


How do replace the rear door handle on 97 Chevy astro van?

how do you get the door open