answersLogoWhite

0


Best Answer

The answer is too involved to answer here. Buy a repair manual ($12) at most auto parts stores. There you will find detailed instructions. The repair manual at the parts house is too generalized. You won't find enough details in the manual to be helpful. Find a manual SPECIFICALLY for Thunderbirds. In the interim, the upper ball joints are easy to replace. Simply purchase CONTROL ARMS for your Thunderbird. The ball joints are pressed into the new control arms. You will have to jack the front end up to release pressure from the front tires/wheels. At the bottom of the control arm, you will find a pinch joint that is held by a pin and bolt. Using a deepwell 18mm socket, remove the nut and gently tap out the pin with a hammer. Ford recommends that you use a new pin and bolt(this is provided with the new control arms). Use a piece of rope or heavy twine to secure the VERTICAL attachment so that it won't fall forward/backward damaging the tie rods. Now proceed to the upper control arm attachments. On each side of the strut (at the upper attachment points)you will find two bolts that attach the control arms to the upper inside of the fender. The boltheads are attached to locking tabs to keep the boltheads from turning when you are tightening the nuts on the inside of the engine compartment. Using an 18mm socket or wrench, remove the nuts (you will find them inside the engine compartment). The forward nuts will be easy to remove while the nuts near the firewall will be a pain in the ass. The passenger side rear nuts are cramped by the air conditioner compressor while the driver side rear nuts are cramped by the brake master cylinder. A socket will be useless as you don't have adequate room. I find that a closed end ratcheting wrench (ask the folks at the parts house for one, an 18mm will usually cost $20)does the trick nicely. The lower ball joints are a different story. Unless you have a hydraulic press, take it to a mechanic. It's worth the extra cost to have them repair it.

User Avatar

Wiki User

18y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you replace the ball joints on a 1993 Ford Thunderbird?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What is the tire size of a 1993 Ford Thunderbird?

1993 Ford Thunderbird tires are generally 15 inches.


Where is the fuel filter located on a 1993 Ford Thunderbird LX?

Where is the fuel filter on 1993 Ford Thunderbird LX


How do you replace a fuel pump for a 1993 Ford Thunderbird?

The fuel pump for a 1993 thunderbird is located in the fuel tank. the tank needs to be dropped, then the pump is accessed through the tank top.


How do you replace cv joints on a 1993 Ford Festiva?

It is best to replace the whole axle, Its easy to do not to mention pretty inexpensive....


Were do you put refrigerant in 1993 Ford Thunderbird?

Yes


Did 1993 ford thunderbirds have front wheel drive?

No , the 1993 Ford Thunderbird is rear wheel drive


How do you replace ball joints on a 97 Ford Thunderbird?

The ball joints on a 97 Ford Thunderbird are replaced by placing the vehicle on jack stands, removing front wheel and rotor, and unbolting the steering knuckle. A ball joint puller is then used to remove the ball joint and a special installer tool is used to press the new one into place.


Is 1993 Ford thunderbird AOD or AODE transmission?

aode


Will a 1992 ford thunderbird transmission go into a 1993 Ford Ranger 4x4?

yes


Where is the water pump located on a 1993 Ford Thunderbird?

The water pump is located in the middle of the front of the engine. The water pump is fairly easy to reach and replace.


Will a door off a 1993 thunderbird fit a 1992 thunderbird?

yes most MN12 Ford Thunderbird/Cougar parts as far as body will interchange


Where does the trunk drain hoses go on a 1965 Ford Thunderbird?

How do you replace the trunk drain hoses on a 1965 thunderbird.