0
How do you replace the belt on the drive shaft pulley on a White LT 12 Lawn Mower?
Wiki User
∙ 12y ago
You need to remove the underdeck to replace the belt.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you remove the drive pulley off the shaft of a GT262 riding mower?
Use a puller so you do not bend the pulley.
Drive belt from engine to mower deck on craftsman mower won't stay on idler pulley?
you probably have a bad bearing
How do you replace a drive belt on a 38yard machine lawn mower?
How do you replace a mower deck belt on a stx38 hydro
How do you adjust drive control craftsman e z walk mower?
If your mower is slipping while drive is engaged you may need to turn the adjusting nut at the cable entrance to the hand control. Turn the adjusting nut (cylinder) counterclockwise with a little crescent wrench. This makes the belt tighter. If this does not fix the problem then you will probably have to replace the belt and also the blade adapter and pulley. The pulley wears down with mower usage.
How do you change the belt on a ranch king riding lawn mower?
You can change the drive belt, on your lawnmower, by loosening the tensioner pulley. With the tensioner pulley, loosen the drive belt will come off and can be replaced.
How do you replace drive belt on a slt 1550 club cadet?
I just changed my drive belt on my Cub SLT 1550...first, you must remove mower deck, then crawl under tractor and remove bolt that holds the mower belt pulley and the centrifugal clutch (you will need to use something to hold the shaft so it doesn't spin when you try to loosen the bolt from the shaft). Once you get this far, you can lower the mower belt pulley & the cetrifugal clutch & finally the drive belt pulley. Now you can remove the drive belt. Install new drive belt & make sure you put all parts back the way they were removed...it does take some work, but you can save about $200 doing it yourself VS dealer.
If you take the deck off a lawn mower will it go faster?
Answer No, it won't go faster, but it may accelerate more quickly. Problem with removing the mower deck is if you pull out in a higher gear you'll run the risk of wheelie-ing backwards onto yourself... hurting you and the tractor. If you need to go faster, the easy way is to replace the drive pulley on the engine with a larger diameter pulley. You may need to buy a longer belt to accommodate the larger pulley.
Replace the AC drive belt on Geo Metro?
Begin by loosening the tensioner pulley. Take the old air conditioning drive belt on. Put the new air conditioning drive belt on and tighten the tensioner pulley.
Drive belt keeps coming off riding mower?
You either have a bad or loose pulley, a stretched belt or a tensioner that isn't working right.
How do you change drive belt on toro lawn mower?
The mower should be drained of gas and drain the motor oil before starting procedure. Disconnect spark plug wire from spark plug. . Motor side of the belt: . Remove two bolts under the lawn mower body which holds the top cover over the drive belt. Remove the belt guard that is around the pulley on the crank shaft. Then work the belt around the blade and off the the drive pulley. . While blade is removed, sharpen or replace as necessary. . Transmission side of the belt: . Remove the "S" clip on handle for speed / traction cable Remove the plastic "Rear Baffle" two screws on each side on frame in front of rear wheels one screw in the rear . With the baffle removed, rotate the drive shaft and transmission to gain access to the pulley drive belt guard, it is held in place with three screws. . Once belt guard is removed, you can easily remove the drive belt . Reverse procedure to replace the belt. . Lubricate drive Axel bearings, wheel bearings, control cables, as necessary. Replace all fluids as necessary.
How do you replace the drive belt on a John Deere L100 Lawn tractor?
You must back out three bolts which hold plastic cover over left side spindle pulley first. After cover is removed (or at least two rear bolts are removed allowing cover to be pulled up ) work belt onto this pulley and reinstall bolts on cover. Then, you must loosen idler pulley next to pulley you just placed belt on as to thread belt onto idler pulley which has a metal fence mounted on pulley shaft to keep belt on this idler. Belt must then be threaded around on/off pulley and right spindle pulley and drive pulley.
What is effective length of lawn mower traction belt?
It depends on the size of the drive pulley to the cutter pulley. The shorter the belt is the less slack is caused and therefore the more traction is maintained between the belt and pulleys
