Headlights Tail and Brake Lights
Mazda Protege

How do you replace the brake light bulb on a 1998 Mazda Protege DX?

282930

Top Answer
User Avatar
Wiki User
Answered
2018-04-27 15:43:27
2018-04-27 15:43:27

Pop the trunk, behind where the brake lights are, there is probably a plastic/rubber cover with screws in it, remove it, and then there should be some screws holding the lens in place, remove those, pull the brake light lens from the outside of the car, twist the wires to undo them from the lens, and go from there.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


Above the brake pedal,its black plastic.

You have to go inside the trunk and remove the circular plastic covers from behind the lights. Then you have to unscrew the entire light and you can access the bulbs to replace them.

Remove the high mount brake light retaining screws from your Mazda Protg. Remove the high mount brake light wiring harness. Reverse the process to install your new high-mount brake light.

Probably a brake light switch problem. May be able to adjust, or may need to replace. I just replaced the brake light switch in my 1998 Mazda Protege LX and the problem came back. I believe the cruise control could be shorting out the brake light switch.

there is a brake switch under the brake pedal. This is a button that pretty much controls the break lights. you might need to replace this or look through the fuse box under the hood. (blue 15) is the fuse that powers the brake lights.

Typically the light will remain on if the fluid is low, or maybe the ebrake just pulled just enough that it is on..... or the switch that is triggered by the handle is faulty

To change a brake light you need to open the trunk and remove the cover behind the light. Pop out any clips using a screwdriver or needlenose. Using a 10mm deep socket, pull off the three nuts holding the light on. Once you pull the light off you can twist out each light by turning counterclockwise about 1/4 turn.

2001 Mazda Protege center high mount stop (third 3rd brake light) light bulb lamp replacement: Purchase the correct replacement center high mount stop (third 3rd brake light) bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the center high mount stop (third 3rd brake light) bulb replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. If there are multiple bulbs, you may want to consider replacing all at the same time in order to keep brightness and color equal (optional).

try finding the fuse box and look for the brake light fuse on see if it is broken

brake lights dont work

To replace the brake light on a 2000 Ford Explorer, remove the screws holding the brake light in place. Gently, but firmly, pull the brake light out of the vehicle and replace with a new one.

How to replace a brake light on a nissan Tiida hatch back.

How can one replace a cornering light on 1990 Mazda dx

2003 Mazda Protege center high mount stop (third 3rd brake light) light bulb lamp replacement procedure: Purchase the correct replacement center high mount stop (third 3rd brake light) bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the center high mount stop (third 3rd brake light) bulb replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. If there are multiple bulbs, you may want to consider replacing all at the same time in order to keep brightness and color equal (optional).

To replace your brake light, you need to unscrew the brake cover from the inside of the trunk. Then you will be able to pull the old bulb out and replace it.

Open the trunk. Turn the socket counterclockwise and remove. Then gently pull out the light bulb. Place the new bulb in the socket and replace the socket into the lens by turning clockwise. Replacement light bulb #3652.

how to replace the brake light switch at the pedal of a 2001 ford zx2

how to replace brake light bulb fiat doblo van

AFAIK that means a malfunction in the Electronic Brake Distribution System. It may be a temporary glitch, take the car to a dealer and ask them to scan the error codes to diagnose the problem.

If there is no brake lights on a 1998 Mazda pickup, check the fuse. If the fuse has blown, the lights will not work.

Your brake light is probably brake fluid low or emergency brake on. Rear brake lights are replaced by removing the lens and replacing the dual filament bulb.

How do you replace the third rear brake light in a 2005 buick allure

The HOLD light means you have an electrical problem with your transmission. See your mechanic ASAP.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.