0
Usually there are screws holding the lens in the tail light- remove these. Then there are more screws holding the tail light to the body- remove these. The pull the wiring out & there should be a plug- unplug & plug replacement into that plug & reinstall in reverse order. hope this helps, Dan I had to get under the Jeep and remove a rubber piece between the rear tire and the bumper to get access to the wire because the wire is too short to come all the way out of the hole on the Jeep's body. It is very easy to do.
What else can I help you with?
How do you replace the light bulb of the headlight on a 1998 Chevy Prism?
the headlight assembly needs to come out in order to replace the bulb.
How do you replace rear brake lights on a 1998 Ford Ranger?
There are two screws on the outside of the tail light assembly. Remove these two screws (keep them) and the assembly should be able to be removed from the truck. Carefully twist the socket out of the tail light assembly. Pull the old light bulb out of the socket and replace with new. Insert the tail light assembly into position in the truck bed and replace the two screws.
How do you replace a marker light on the right front for a 1998 Isuzu trooper?
To replace the right front marker light on a 1998 Isuzu Trooper, first, ensure the vehicle is turned off and the keys are removed. Open the hood and locate the marker light assembly; then, remove the screws or clips holding the assembly in place. Carefully pull the assembly out, disconnect the wiring harness, and replace the old bulb with a new one. Reconnect the wiring, secure the assembly back in place, and test the new light to ensure it works.
How do you remove brake light 1998 slk 230 Mercedes?
To remove the brake light on a 1998 Mercedes SLK 230, first open the trunk and locate the light assembly. Remove the screws or clips securing the assembly, then gently pull it out from the body of the car. Disconnect the wiring harness from the back of the light assembly and replace the bulb if needed. Finally, reinstall the assembly by reversing the process.
How do you replace rear parking light lens on 1998 Dodge Dakota?
THERE IS NO PARKING LIGHT LENSE FOR THE REAR. IT'S ONLY THE TAIL LAMP ASSEMBLY!
How do you change a rear parking light lens on 1998 Dodge Dakota?
I believe it is 2 torx screws inside the tailgate holding the assembly. Have to replace the whole assembly.
How do you replace the dome light switch on a 1998 mercury tracer?
To replace the dome light switch on a 1998 Mercury Tracer, first, disconnect the negative battery terminal to ensure safety. Then, remove the dome light assembly by gently prying it down from the ceiling. Disconnect the wiring harness from the old switch and replace it with the new one, ensuring a secure connection. Finally, reattach the dome light assembly and reconnect the battery terminal.
How do you replace the brake light bulb on a 1998 Chevy silverado?
when you put the tailgate down there will be two screws to remove the light assembly. then to open the light assembly it requires a 1/4" nut driver I believe? good luck its easy
How do you remove a 1998 infiniti I30 tail light?
To remove the tail light from a 1998 Infiniti I30, first, open the trunk and locate the tail light assembly. Remove the screws or bolts securing the tail light, typically found near the trunk's edge. Gently pull the tail light assembly out, disconnect the wiring harness by pressing the release tab, and then remove the assembly completely. Finally, replace the bulb if needed before reinstalling the assembly.
Do you have to drop the fuel tank to replace the fuel pump on a 1998 jeep wrangler?
Yes.
How do you replace the throw out bearing for a 1998 Jeep Wrangler?
you have to take the tran out. then it will slide off
How do you replace outside door handle on a 1998 jeep wrangler?
you need to remove the inside door panel to get access to the inside, remove the clips holding the door handle assembly and the whole thing comes off
