0
Usually there are screws holding the lens in the tail light- remove these. Then there are more screws holding the tail light to the body- remove these. The pull the wiring out & there should be a plug- unplug & plug replacement into that plug & reinstall in reverse order. hope this helps, Dan I had to get under the Jeep and remove a rubber piece between the rear tire and the bumper to get access to the wire because the wire is too short to come all the way out of the hole on the Jeep's body. It is very easy to do.
What else can I help you with?
How do you replace the light bulb of the headlight on a 1998 Chevy Prism?
the headlight assembly needs to come out in order to replace the bulb.
How do you replace rear brake lights on a 1998 Ford Ranger?
There are two screws on the outside of the tail light assembly. Remove these two screws (keep them) and the assembly should be able to be removed from the truck. Carefully twist the socket out of the tail light assembly. Pull the old light bulb out of the socket and replace with new. Insert the tail light assembly into position in the truck bed and replace the two screws.
How do you replace a marker light on the right front for a 1998 Isuzu trooper?
To replace the right front marker light on a 1998 Isuzu Trooper, first, ensure the vehicle is turned off and the keys are removed. Open the hood and locate the marker light assembly; then, remove the screws or clips holding the assembly in place. Carefully pull the assembly out, disconnect the wiring harness, and replace the old bulb with a new one. Reconnect the wiring, secure the assembly back in place, and test the new light to ensure it works.
How do you replace rear parking light lens on 1998 Dodge Dakota?
THERE IS NO PARKING LIGHT LENSE FOR THE REAR. IT'S ONLY THE TAIL LAMP ASSEMBLY!
How do you change a rear parking light lens on 1998 Dodge Dakota?
I believe it is 2 torx screws inside the tailgate holding the assembly. Have to replace the whole assembly.
How do you replace the brake light bulb on a 1998 Chevy silverado?
when you put the tailgate down there will be two screws to remove the light assembly. then to open the light assembly it requires a 1/4" nut driver I believe? good luck its easy
Do you have to drop the fuel tank to replace the fuel pump on a 1998 jeep wrangler?
Yes.
How do you replace the throw out bearing for a 1998 Jeep Wrangler?
you have to take the tran out. then it will slide off
How do you replace outside door handle on a 1998 jeep wrangler?
you need to remove the inside door panel to get access to the inside, remove the clips holding the door handle assembly and the whole thing comes off
How do you replace fog light 1998 e320 Mercedes Benz?
To replace the fog light on a 1998 Mercedes-Benz E320, first, ensure the vehicle is turned off and the keys are removed. Access the fog light by removing the cover or the entire fog light assembly from the bumper, usually held in place by screws or clips. Disconnect the wiring harness from the old fog light, replace it with the new bulb, reconnect the wiring, and reassemble the cover or fog light assembly. Finally, test the new fog light to ensure it’s functioning properly.
Why does blinker on passenger side of 1998 Chevy 2500 not work?
The rear tail light assembly had problems with the sockets and circuit board. My guess is you will need to replace the socket and circuit board assembly for the passenger side rear tail light.
How do you replace a bulb in tail light of 1998 Ford Taurus station wagon?
To replace the tail light bulb in a 1998 Ford Taurus station wagon, first, open the trunk and locate the tail light assembly. Remove the screws or clips securing the assembly, then gently pull it away from the vehicle. Twist the bulb socket counterclockwise to release it, replace the burnt bulb with a new one, and reassemble by reversing the steps. Ensure everything is secured before closing the trunk.
