Mercedes-Benz
DIY Projects

How do you reset service indicator on 2007 Mercedes R350?

123

Top Answer
User Avatar
Wiki User
Answered
2014-11-20 06:19:06
2014-11-20 06:19:06

A person can reset this indicator by fixing the problem that caused it to go off. They can also use an OBD scanner to clear the codes and the indicator.?æ

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


How do you reset the service indicator on 2007 Mercedes vito


How do you reset a service indicator message on a 2007 Mercedes Benz GL450



You have to have the computerized equipment- get to a mechanic/dealer who has one.


Go to yuotube and type there this question.




how to reset the brake service indicator on mini cooper s 2011


jaguar s type twin turbo diesel 2007. how to cancel "service required" indicator.


Magic and luck, with a little skill. Good luck.


Need help resetting the maintenance service indicator on the 2007 GL450. I changed the oil at 6500 miles and reset the indicator 1st time (service A). Now the Service B light is on and odometer only reads 11,000 miles. I read the manual, it says light should not be reset for oil changes done outside of recommended service. I accidentaly reset it first time now it is out of sequence. Any help would be greatly appreciated. __________________


use trip computer switch located on wiper lever when service indicator comes up press in button on side of lever



any shop or dealer should be able to reset it, they have to plug into your car just under and to the left of your steering wheel, using a handheld to pull and clear any codes. hope this helps. or try this : 1. Turn Ignition key to position1 2. Press and hold reset button for the trip meter 3.Switch ignition ON 4. Keep Depressed for 10 secs. Service indicator will flash. Release reset button within 5 secs. There will be an audible signal when reset completes & service indicator goes out. * if reset button is not released within 5 secs , the service interval indicator will not be reset but will stop flashing. Good Luck!


To reset the service indicator wrench:Hold down the odometer reset button with the ignition offWait for the trip indicator to show 0's. Then turn the ignition on, but don't start the carLet go of the reset button, and press the M button.


disconnect the battery for 10 mins or turn the ignition switch back and fourth with the key in it


how do u reset service light on 2007 plate bravo


You can clear the service light through the OBD2 port, which is located under the dashboard on the driver's side. www.ebay,com and search for OBD2.


Start the engine. Then press the C/T button . Then tab the the computers setup with the step button until you see 0 miles to service. After you see that, you just simply press the reset button, and the 0 miles to service, should change to 3,000 miles to service.


Beaverton Toyota, Oregon, provides a list of the steps to reset the service indicators for a variety of Toyota models, also Scion. Go to: How To Reset Maintenance Light ( http://www.beavertontoyota.com/service/tips.htm ) Find your make and year, and go to the list, thus ... --- "Reset Engine Oil Replacement Reminder Light" --- Find your model and follow the detailed steps. For 2008 Avalon, the list is at: http://www.beavertontoyota.com/service/pdf/08maintlight.pdf


When your car is serviced at a non-vw garage or at home by yourslef, the ecu doesnt know its had a service, so the service indicator stays on. To reset it: -(with the ignition off and keys out) press and hold the mile reset button -turn ignition on -wait until the display goes like '--' -turn ignition off and keys out and release button


How to reset the service traction control light on a 2007 Chevy Sub?


I am not sure about the 2007 model. 2004-200 Models: The answer is in the manual. If you do not have the manual: After you turn on the engine, hold the trip reset button until the service remainder resets.


If you are aking abouthe maintenance light reser here are procedures: Close the doors, press and hold the reset button on the left, insert the key and turn it to on position, wait about 10 seconds until the indicator goes off and then release the reset button.




Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.