answersLogoWhite
notificationBell

Top Answer
User Avatar
Wiki User
Answered 2009-11-21 01:59:02

There are 3 stages

locate the obd plug and find pin 8 then

turn ignition to pos 2

with a fused wire ( a piece of wire with a fuse in it)

ground pin 8 for 4-5 seconds

turn ignition off

repeat this procedure 2 more times but for 8-12 seconds and then the service indicator will be reset.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Related Questions



hello drummond batteries and i don't now how to reset the service light can you help its Holden vectar v6 2002


the light can only be cleared by a scanner take it to a qualified mechanic


It is important to pay attention to the warning lights on a car. To reset a service engine light on a car, a person must fix the problem causing the light to go off.


You need to have the cause of the codes repaired before the light can be successfully cleared.


You can disconnect 1 battery cable for about a minute to reset it but if you don't fix the problem it will be back on shortly.


I have a 2002 Millenia-S and removing and reattaching the + battery cable does reset the check engine light.Answertry unhooking the positive cable to the battery...this works on my 97 millenia


The serv light means that there is a problem with the ecu,u will have to take it to a garage to get looked at


Go to auto zone and have the codes read for free.


http://www.unofficialbmw.com/e36/electrical/e36_reset_service_lights.html Here lies your answer


Read the drivers hand book or car manual. It is easy to do.


Disconnect the battery. I had a problem with my service soon light coming on very light, not bright and I was told it could have something to do with not closing my gas cap tightly.


In order to reset the service engine light, you need to locate the fuse box under the hood on the driver's side. The light should not be reset unless you are absolutely sure service is not needed.Ê


get your hands on a code reader or disconnect your battery for a few minutes


how do i reset timing belt light on 1hz


AnswerThe answer can be found in your owner's manual.Key on, engine off.Press "step" until "0 miles to service" is displayed. Press and hold "reset".


The light is one because there is a problem with the emissions system. Once the problem is corrected the service tech will reset the light.


Once you have repaired the cause of the light, it will reset itself.Once you have repaired the cause of the light, it will reset itself.


You can't reset that light...there is no such thing as a 2002 Honda Element...they didn't come out until 2003.


need to reset the computer go to auto zone and they will usually do this for free but just tell them you have a check engine light on


It is very easy to reset the check engine light on a 2002 Volkswagen Cabrio. The negative battery cable can be taken off for one minute and replaced to reset the light.


A 2002 Jeep Wrangler does not have a reset switch.


I used this procedure to reset my 2002 s40 services light (it should work for 2008 s40 also). a) insert ignition key and turn it to the 1st click - no lights on bottom of the instrument panel should be light up b) press and hold trip odometer reset button, and turn the ignition key to the 2nd click - the row of lights at the bottom of the instrument panel should come on c) after about 5 secs the lights should go off except the Service reset light - it will blink d) when the Service reset light has blinked for about 3 times - release the odometer reset button e) the Service reset is complete Note: This procedure cannot be used to reset Check Engine light - it requires an OBD2 code reader.


With the engine turned on and someone in the driver seat. Hit the step button until 0 miles to service appear, hit RESET. A beep will sound and it is done.


http://www.benzworld.org/forums/w163-m-class/1189404-how-do-i-reset-service-indicator.html