0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Can you run two 15 audiopipe subwoofers off a 550 RMS monoblock amp?
You can but it probably won't hit that hard. I don't know the subs rms but if there 15s should be atleast 800 to 1000 rms . Get 1 Audiopipe 1500 monoblock . That will push them
Can you hook both a subwoofer and speakers to 1 amp If so do I need to buy a amp that's even more powerful Then what the sub requires?
You can connect a sub and speakers to one amp, depending on how many channels your amp has. A 4 channel amp will be able to run one (or two) subs using two channels (one bridged* sub or two subs) and two speakers running one channel each. A 2 channel amp will run 2 speakers or one bridged sub. A 6 channel amp will run one bridged sub (or two subs), 2 front speakers and 2 rear speakers. In my opinion, you will get the most performance, depending on which amps you use, by using a monoblock amp for your sub and an amp with enough channels to run all of your speakers. # Bridged = putting together the power of two channels to run one sub or speaker. Note: not all amps are bridgeable.
Low pass filter amp?
low pass is for subs only it tells the amp to play low frequency only dont run subs on high pass or off
How do you connect two amps to four subs?
Run a 2 sub per amp set-up. Get a distribution block for you power wire to split the power wire. You can run the remote wire from your stereo to one amp and then from the amp to the other amp. you will also need 2 sets of RCA's Easy way is too get a 4 channel amp to power 4 subs.
What do you set your amp to for 2 12 subs?
to mono if your amp will allow, also this is for single voice coil. otherwise run in mono parallel to run dual voice coils.
How big of an amp do you need for two 1200 watt subwoofers?
Depends on what your willing to spend.. For two 1200 watt subs I would go with a 1200 watt amp and run both of then 600 watts ( you don't want to always run subs to full power, because the voice coil might blow or you will light your subs on fire). If your feeling brave you can run a 2000 watt amp 0_o that will annoy your neighbours, but make your car bump!
What is the risk of putting 2 12 inch subs to a stock Bose system with stock amplifier?
your going to do alot of work and the results are going to be meager the stock amp won't have the power to run the subs properly. you my burn out the subs. you should get an amp which can power those 2 12 inchers
Can you Run 4 300rms Subs On a 1200 watt amp?
i was about to hook up 2 12'' mtx tr45 and 2 10'' renegade25 on my 1400watt amp too
What amp I need for jl audio w6 12''?
You need to run at least 500 watts from a real amp to push the speakers to potential without overheating. I am running a 1x1000watt monoblock kicker amp at both of them and it is all I ever wanted and it will handicap anybody within 100ft of the car.
Bridge two subs to a four channel amp?
If you amp is bridgeable you run + sub wire to ch 1 + then the -sub wire to the - of ch 2 of the amp. The same with the other sub + ch3 - ch4 that's how to bridge your amp.
What is the line out on a fender amp?
To run a monitor speaker or to connect several amps in series to pre-amp your amp.
Can you use a 1000 watt amp and a 400 watt amp on 2 subs can they be wired together to give you 1400 watts for both subs?
no you can't. if you want to run separate amps for your subs they both have to be the same amperage and preferably same model. you can use the 1000 w amp on the subs and get a nice amount of bass depending on what size and model subs you have. then just use the 400 w amp for your mids and run the highs off the radio lines. try that and you will hear some good sounds. you will also need a crossover as well. hope that helped.
