answersLogoWhite
Isuzu Rodeo

How do you set cam gears on Isuzu 3.5 engine?

345

Top Answer
User Avatar
Wiki User
2012-05-28 03:56:27
2012-05-28 03:56:27

using special tool, j-42686 pre- load the sub gear so the teeth are aligend with the cam chaft teeth then retain the sub gear sucurely with a m5 bolt inserted from the back side of the camchaft gear assmbly

1

Related Questions

User Avatar

How do you set cam timing of a mazda 626 l 1.8?

User Avatar

You can set the injector pump timing on a 4HF1 Isuzu engine by adjusting the fuel injection screw. The adjusting screw will restrict the amount of fuel to be injected.

User Avatar

With the the crank pulley at tdc, the white mark on the cam gear lines up with the center of the rocker shaft.

User Avatar

The timing marks on your Isuzu 4hf1 engine can be set by looking at the timing marks on the timing belt pulley. The timing belt marks are facing towards the front of the automobile.

User Avatar

It tells the engine management system the cam position in operation which set up engine timing and speed data for the ECM.

User Avatar

align the crankshaft pulley mark with mark on oil pump housing, and align marks on cam gears with marks on rear cover, then install timing belt.

User Avatar

The cam timing on a 4.6 SOHC engine is set by aligning the timing marks of the timing chain to the cam sprocket. This sets the initial timing based on factory settings.

User Avatar

you cant set "timing" you have to have a scanner to set cam sensor to 0 +or-2

User Avatar

It does NOT have a timing belt, That engine has a timing chain and gears.

User Avatar

how to set the timing on 3.5 liter engine on a trooper 98

User Avatar

the is 4.5 liters in 1 hour used in generator set

User Avatar

How do you set the timing on a 92 Isuzu Rodeo 3.1?

User Avatar

If you are haveing trouble setting time on the 3.2 v6 it is because this engine is set on the number two cylender, NOT number one top dead center (as most vehicles are set), Look up at your local Honda or Isuzu dealership and get the Timing Procedure from them. I say Honda Dealership because the Honda pass port uses an Isuzu 3.2 engine.

User Avatar

No you cannot. It will just eat the lobe off the cam further. You will have to replace the cam and lifters. be sure to change the oil and filter several times after job is finished. It would be wise to replace the timing chain and gears as a set.

User Avatar

The timing on that year engine is computer controlled and you must have an engine scanner to set the timing. That engine has a cam and crank sensor and they must be in correlation / TIME with each other. Are you will have a check engine light on and poor performance.

User Avatar

timeing is controled by a key way under the flywheel, if its off te keyway is bent, there is also timing marks on the crankshaft and cam gears. these need to be lined up on top dead center. be careful as not to set them 180 degrees off or the engine will backfire.

User Avatar

I have the same question! I think it is the result of an aftermarket cam set up.

User Avatar

there is 3 marks on the timing chain. 2 are exactly 16 links apart and the other is 22 from either of the 2. the engine should be at top dead center. line the 2 (16 apart) marks with marks on your cam gears and the 3rd with your crank gear. torque cam bearings to 100 inch lbs.

User Avatar

The dot on the bottom gear goes straight up and the dot on the top gear points straight down when the timing chain and gears are installed correctly.

User Avatar

the timing mark (z) of injection pump and the mark (z) to cam shaft the other markof cam shaf (y) to the idler geer (y) and the (x) mark of idler to main shaft (x) mark

User Avatar

Gears of war is not set on Earth it is set on Sera, so its not our future its their present.

User Avatar

how many degrees do you set an injector pump of 4hf1 isuzu truck

User Avatar

It depends if it is an OHV(pushrod motor) or a s.o.h.c./d.o.h.c. motor. Ohv engines can have a timing chain set that allow for adjustment, to be installed. You can also install crank keyways that adjust the timing by moving the crank cam gear the required degree/s. Overhead cam engines can have cam gears installed that allow for cam adjustments.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.