Ford Probe

How do you set timing marks on a 94 ford probe?

232425

Top Answer
User Avatar
Wiki User
2006-02-06 23:59:45
2006-02-06 23:59:45

1st take out the 1st cylinder spark plud bring the cylinder to the top then set the rotor to the mark before the 1st cylinder firing pin then on the distributor gear there in a thin line line that up wit line on the block then slide in the distrubutor then hook up everything if it doesn't work u did domething wrong

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

where are timing marks on 89 ford probe 4 cylinder I have the bottom not the top

User Avatar

There are no timing marks. The timing is controlled by the PCM. Power control module. It is not possible to set the timing with a timing gun.

User Avatar

To set the ignition timing on a Ford Probe GT 95 with an MX engine, remove the two 12 mm head bolts holding the distributor in place. Then rotate the distributor to set the ignition timing.

User Avatar

The timing marks for a 2002 Ford Explorer are located on the timing chain and cam shaft sprocket. They must be aligned with each other to set the initial timing.

User Avatar

It has no timing marks because the ignition timing is set by the computer and isn't adjustable.

User Avatar

The timing marks are marks on the front main pulley. The marks indicate when a certain piston is at the top of its stroke. You can turn the pulley to a certain position, aligned with the timing marks, and no that piston is at the right position to set the timing.

User Avatar

there are two dots on the distributor they have to be lined up on tdc

User Avatar

You can set the camshaft timing on your automobile by lining up the timing marks. There will be timing marks on the front main pulley and timing marks on the camshaft.

User Avatar

The timing marks on your Isuzu 4hf1 engine can be set by looking at the timing marks on the timing belt pulley. The timing belt marks are facing towards the front of the automobile.

User Avatar

clean on the front of the pump on top where it bolts on the motor there are timing marks there line up the long marks to set the timing.

User Avatar

there are 2 marks on the gears you have to line them up

User Avatar

May be computer controlled and not adjustable

User Avatar

how to set the timing marks on a 1995 Mitsubishi Montero

User Avatar

you set timing by the marks on the cam shaft and the crank shaft. they should point at together to make it run right.

User Avatar

if you look near the center bolt on your main pulley attached to the crank you will find a small arrow, use a white paint pen to mark it so it is visible, hook up your timing light and time using the timing marks attached to your engine block

User Avatar

hey i have a 73 ranchero 400ci and just set the timing at 6 degrees advance.

User Avatar

1998 and newer have no timing marks. Timing cannot be adjusted.

User Avatar

1970's to 1980's had a Magnetic Probe receiver. Digital readout vs. using a Strobe inductive type. I own an 85' Chrysler 5th Ave 5.2L and I can't find actual timing marks so Magnetic Probe in my case is an alternative.

User Avatar

The timing is set by timing marks on the crankshaft pulley. Using a timing light the light will sync with the engine and show if the marks line up properly. To adjust the timing the distributor is turned slightly. There is a clam and bolt under the distributor, loosen these just a bit to be able to move the distributor.

User Avatar

how to set the timing marks on a single cam dodge neon

User Avatar

how do you set or check the timing on a 99 ford expedition?


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.