0
How do you switch off the air bag and seat belt dashbord warning lights?
Wiki User
∙ 14y ago
Snip the wires going to the light. Then put a jumper across the snipped wires so the control module thinks the light is working.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Does the vw polo have seat belt warning lights?
The newer VW Polo cars do have seat belt warning lights. Older models from the 1970's and 1980's are not equipped with this light system.
How do you turn off the seatbelt sensor in your 2003 Explorer?
- Switch on without starting the engine - Wait till the seat belt warning light switches off - buckle and unbuckle the belt three times ending with the belt unbuckled - Switch on the head lights - Switch off the head light - the seat belt warning light will light for few seconds and once it swiches off buckle and unbuckle the bet one more time - switch off Siamand ORRRR, try fastening your seatbelt. tard
Why is my 2002 Kia Spectra battery and brake warning lights on?
broken belt
Does the warning light stay on when the timing belt needs changing on a 1996 Toyota landcruiser?
the warning lights comes on indicating that the timing belt needs to be changed. even once the timing belt is changed, the warning light will stay on until is it reset.
Why would the panel lights go in a 1997 960 Volvo?
When my Volvo broke an alternator drive belt the majority of the warning lights came on.
Why is the seatbelt airbag light flashing in a 2000 Ford Explorer xls?
Warning lights are important to pay attention to and know warning lights. If seat belt lights flash, and an air bag light flash, it means there are problems with both parts.
Can you show me the dashboard warning lights for Volkswagen beetle 2001?
Some of the warning lights available on the VW Beetle 2001 include a low fuel warning and a seat belt warning. Some other common ones include over-heating engines and the need for an oil top-up.
How do you disable seat belt alarm on 2013 dodge ram 1500?
First option is obeying the law and wearing your seat belt. Second option The Enhanced Warning System (BeltAlert) can be enabled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. DaimlerChrysler does not recommend deactivating the Enhanced Warning System (BeltAlert). 1. With all doors closed and the ignition switch in any position except On or Start, buckle the driver's seat belt. 2. Turn the ignition switch to the ON position and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver's seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver's seat belt remains unbuckled.
Volvo 850 year 1996 Flashing map all warning lights engine stops?
This sounds like what happens when your timing belt breaks.
How do you remove a dodge Dakota 2007 seat belt reminder?
1. With all doors closed and the ignition switch in anyposition except On or Start, buckle the driver's seat belt.2. Turn the ignition switch to the ON position and waitfor the Seat Belt Warning Light to turn off.3. Within 60 seconds of turning the ignition switch to theON position, unbuckle and then re-buckle the driver'sseat belt at least three times within 10 seconds, endingwith the seat belt buckled.NOTE: Watch for the Seat Belt Warning Light to turn onwhile unbuckling and off while re-buckling the seat belt.It may be necessary to retract the seat belt.4. Turn the ignition switch to the LOCK position. Asingle chime will sound to signify that you have successfullycompleted the programming.1. With all doors closed and the ignition switch in anyposition except On or Start, buckle the driver's seat belt.2. Turn the ignition switch to the ON position and waitfor the Seat Belt Warning Light to turn off.3. Within 60 seconds of turning the ignition switch to theON position, unbuckle and then re-buckle the driver'sseat belt at least three times within 10 seconds, endingwith the seat belt buckled.NOTE: Watch for the Seat Belt Warning Light to turn onwhile unbuckling and off while re-buckling the seat belt.It may be necessary to retract the seat belt.4. Turn the ignition switch to the LOCK position. Asingle chime will sound to signify that you have successfullycompleted the programming.
How do you disarm the seat belt alarm in a 2008 dodge 1500?
if the ignition is cycled, driver's seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). The Enhanced Warning System (BeltAlert) can be enabled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. DaimlerChrysler does not recommend deactivating the Enhanced Warning System (BeltAlert). 1. With all doors closed and the ignition switch in any position except On or Start, buckle the driver's seat belt. 2. Turn the ignition switch to the ON position and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver's seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver's seat belt remains unbuckled.
Why did the brake and battery warning lights come on and you lose power steering while driving your 98 Isuzu rodeo?
Did you check the drive belt to see if it broke?
