0
You don't. They have two different sync formats. Same for Wheelock, Gentex, etc. Never mix and match on a circuit > power supply.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What are the sensor data capturing in expert system?
In an expert system the sensor is capturing raw data. This data is used to analyze, examine, organize, and secure data for reporting and visualization.
What element detects change in a control system?
Receptor/Sensor-Recognition of the factor.
Will s light sensor from a 240 light still work for a 12 volt system?
No, you will need to get a step up transformer, it's probably more sensible to get a 12v sensor.
How do you change the o2 sensor in a Volvo 240 dl?
Wait until the car is cooled down. To change an o2 sensor you must have an 7/8 inch wrench or have an o2 sensor wrench. After finding the correct tool for the application you then jack up the car in most cases. Find The o2 sensor in the exhaust system most likely at the front of the car behind the front wheels about 2 feet in. Loosen the o2 sensor with the wrench and unscrew. Reverse process for installation.
How do you measure mechanical frequency?
I assume you mean measure the frequency of vibration of a mechanical system or part. You use a stroboscope, which is a light that flashes briefly and rapidly. You shine the light on the object and adjust the frequency of the strobe by turning a dial until the object stops moving. You then read the dial to determine the frequency. there are steps you have to take to avoid synchronizing to a subharmonic of the base frequency. For example, if the object is vibrating at 100Hz (10ms), running the strobe at 50hz will also stop the motion, as it will pick up every other cycle.
What are amber strobes for fire alarms?
Amber strobes are used with Mass notification systems that are commonly attached to fire alarms system. They are activated to give a visual warning as instructions are passed over a intercom, or loudspeaker system. Many times you will see both amber colored strobes and clear lens used in a single facility. The clear lens strobes will be labeled as fire, and amber will contain no markings.
Where and what is the camshaft position sensor?
the camshaft position sensor is used to synchronize the fuel injection system with the opening of the intake valves. It synchs the cam shaft location with the crankshaft location It can be in a distributor or it can read a tone wheel on the cam shaft.
What is it called when you have a system then a system in case that system fails an exact duplication of the same system not a contingency plan?
Synchronize Back-up System
What memory type is known to synchronize itself with a computer's system bus?
SDRAM
What does syncronize mean?
Synchronize is to calibrate a system to run in unison with itself. Like synchronize my watch with yours to have the same time. Or have a dance team move exactly alike.
How do you make my hazard lights flash like a strobe lights in a 1995 tarus?
To make the hazard lights alternating flash, a kit called a wig wag is added to the flasher system. To have actual strobe lights, then a strobe kit with its own light has to be installed.
Why is it important to synchronize data process models?
It is important to synchronize data to show consistency and completeness of the total system requirement earlier captured in the data model and process models.
What is System Sensor's population?
System Sensor's population is 1,900.
When was System Sensor created?
System Sensor was created in 1984.
Where are the timing marks on a 1994 850 Volvo 2.4?
There are no timing marks to use with a strobe light & engine timing is not adjustable. The engine ECU automatically controls timing of the engine via a camshaft sensor, a crank angle sensor, a throttle position sensor, a coolant temp sensor and many others. If your vehicle is not running well or obtaining poor petrol mileage, obtain a good workshop manual and by process of elimination work out the problem. The 1994 850 has a OBDI error system which can highlight sensor or ignition system errors. The workshop manual you obtain should tell you how to read any flashing codes.
What is sbs sensor?
sensor battery system
The Rogue System Sensor determines if a machine is a rogue system.?
The Rogue System Sensor determines if a machine is a rogue system?
