answersLogoWhite

0

You don't. They have two different sync formats. Same for Wheelock, Gentex, etc. Never mix and match on a circuit > power supply.

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Natural Sciences

What sensor does a automatic wiper system use?

An automatic wiper system typically uses a rain sensor that detects moisture on the windshield. This sensor sends signals to the system to adjust the wiper speed according to the amount of rain detected.


What are the sensor data capturing in expert system?

In an expert system the sensor is capturing raw data. This data is used to analyze, examine, organize, and secure data for reporting and visualization.


What element detects change in a control system?

Receptor/Sensor-Recognition of the factor.


How do you measure mechanical frequency?

I assume you mean measure the frequency of vibration of a mechanical system or part. You use a stroboscope, which is a light that flashes briefly and rapidly. You shine the light on the object and adjust the frequency of the strobe by turning a dial until the object stops moving. You then read the dial to determine the frequency. there are steps you have to take to avoid synchronizing to a subharmonic of the base frequency. For example, if the object is vibrating at 100Hz (10ms), running the strobe at 50hz will also stop the motion, as it will pick up every other cycle.


In a negative feedback which component receives signal from the sensor?

In a negative feedback system, the component that receives the signal from the sensor is typically the comparator or controller. This component evaluates the information from the sensor against a set reference point or desired state. Based on this evaluation, it then sends corrective signals to the effector or actuator to restore the system to its optimal condition. This process helps maintain homeostasis or stability within the system.

Related Questions

What are amber strobes for fire alarms?

Amber strobes are used with Mass notification systems that are commonly attached to fire alarms system. They are activated to give a visual warning as instructions are passed over a intercom, or loudspeaker system. Many times you will see both amber colored strobes and clear lens used in a single facility. The clear lens strobes will be labeled as fire, and amber will contain no markings.


Where and what is the camshaft position sensor?

the camshaft position sensor is used to synchronize the fuel injection system with the opening of the intake valves. It synchs the cam shaft location with the crankshaft location It can be in a distributor or it can read a tone wheel on the cam shaft.


How do you make my hazard lights flash like a strobe lights in a 1995 tarus?

To make the hazard lights alternating flash, a kit called a wig wag is added to the flasher system. To have actual strobe lights, then a strobe kit with its own light has to be installed.


What is it called when you have a system then a system in case that system fails an exact duplication of the same system not a contingency plan?

Synchronize Back-up System


What memory type is known to synchronize itself with a computer's system bus?

SDRAM


What is the disadvantage of strobe using asynchtonous data transfer?

A disadvantage of using strobe signals in asynchronous data transfer is that it can lead to increased complexity in timing and synchronization. Since the strobe signal is used to indicate when data is valid, any mismatch in timing between the data and the strobe can result in data corruption or misinterpretation. Additionally, the reliance on strobe signals can increase the overhead in the system, potentially reducing overall data transfer efficiency.


What does syncronize mean?

Synchronize is to calibrate a system to run in unison with itself. Like synchronize my watch with yours to have the same time. Or have a dance team move exactly alike.


Why is it important to synchronize data process models?

It is important to synchronize data to show consistency and completeness of the total system requirement earlier captured in the data model and process models.


What is System Sensor's population?

System Sensor's population is 1,900.


When was System Sensor created?

System Sensor was created in 1984.


Where are the timing marks on a 1994 850 Volvo 2.4?

There are no timing marks to use with a strobe light & engine timing is not adjustable. The engine ECU automatically controls timing of the engine via a camshaft sensor, a crank angle sensor, a throttle position sensor, a coolant temp sensor and many others. If your vehicle is not running well or obtaining poor petrol mileage, obtain a good workshop manual and by process of elimination work out the problem. The 1994 850 has a OBDI error system which can highlight sensor or ignition system errors. The workshop manual you obtain should tell you how to read any flashing codes.


How can I synchronize multiple remote camera flashes for a professional photoshoot?

To synchronize multiple remote camera flashes for a professional photoshoot, you can use a wireless flash trigger system. This system allows you to trigger all the flashes simultaneously, ensuring that they fire at the same time and produce consistent lighting in your photos.