Want this question answered?
The hose has to be at least at the top of the washer.
The highest overall rating for a front-loading machine is the Maytag MHWZ600TE Front Load Washer. The highest overall rating for a top-loading machine is the GE WPGT9360EPL Top Load Washer. These ratings were collected from consumers and reported at:http://wize.com/washing-machines/products
Having sex on toP of a washing machine while it's going, it provides more creativity and enjoyment
Front-load simply means that the washing machine door is on the front face of the washing machine, rather than a lid that lifts from the of the washing machine (top load). One would 'load' the clothes into the washer through the open front, hence the name front-load.
The difference between a front loader and a top loader washer is that one has a door on the barrel. This type of washer can be seen in most laundromats that handle large loads of clothes This is general an easier washer for people with mobility issues and it uses less water. The door opens like a front door to a house or a car door. The top load washer has its door on the top of the washer and clothes are put down into the opening. The top load washer can be more difficult for people with mobility issues. This type of machine usually uses more water.
After you disconnect all of the cables, you have to remove the handlebar stem (loosen stem bolt half way, then knock the wedge loose by hitting the top of the bolt), remove the top part of the Gyro, then take off the top nut of the headset. Instead of a washer, you'll have the bottom part of the Gyro. You MUST replace the part of the Gyro that's under the headset nut with a headset washer or you'll never be able to keep your headset tight.
The advantages of a front loading washing machine over a top loading washing machine is that with the front loading machines , you can usually hold more laundry equally and efficiently which saves on money and conserves alot more water than normally would
Shut the water off, at the toilet if possible, take the line loose that goes to the tank and see if it is the supply line or the filler valve. I'll bet it's the valve. If you have the type that has a round float that rides up and down on a post, they have a washer in the top with a small hole in it that lets the water in. Rust and corroisen can break off when you shut the water off and it will plug this hole. Hold the shaft so that it doesn't break and twist the top 1/8 turn counter clockwise. The washer is in the top of the stack, black about the size of a quarter. Take the washer out and turn the water on slightly to push out any particles that might block the hole in the center of the washer. Reassemble and I bet it works.
my frigidaire top load washer makes loud noise in the spin cycle
If the handle make a complete or almost a complete turn, it has a washer that makes the seal to stop the water. This washer will sometimes come apart or come off the stem and get stuck in the opening for the water. Take the stem out and replace it. Shut the water off, there is probably a shut off under the sink, take the handle off. It is most likely held on with a screw in the top. The stem is held in with a nut. Take the nut off and the handle unscrews out of the faucdt. The washer is on the bottom of the stem and held on witha small brass screw.
You have to unbolt the cross brace from the radiator support,the windshield washer tank and the over flow tank,then you can work it down and out. I just changed mine and all you have to do is take your overflow tank off and move your power stering res out of the way. take the bracket off the top of the alternator then take the belt off remove the 4 bolts on top and the 2 on bottom then slide it out. you do not have to take the cross brace off or the winshild tank off.
You shut the water off and the fill valve is the type that is in the corner of the tank and the float rides up and down on a shaft? If so, a piece of rust or mineral is plugging the valve. Shut the water off, hold the shaft of the fill valve and twist the top 1/8 turn counter clockwise. The top will come off and where it separates, there is a black washer with a small rod in the center of it. Take the washer out and slightly turn on the water. This will flush out any particles in the line. Shut the water off, replace the washer and put the top back on. This should fix the problem.