answersLogoWhite

0

How do you take apart a spark plug?

Updated: 10/22/2022
User Avatar

Wiki User

10y ago

Best Answer

Not possible without breaking it.

User Avatar

Wiki User

10y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you take apart a spark plug?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What happens if glass falls into spark plug hole?

Um, you probably shouldn't have had glass around the open spark plug hole in the first place. this could make it hard for your spark plug to fit into place, or even send the spark to the cylinder. You will have to take apart the head and remove the glass depending on how big the shard, or piece is.


How do you remove a spark plug nut that is broken in the cylinder. note the actual spark plug itself is out just not the nut and thread around it and you cannot get a spark plug socket on it?

There is a special easy out for this. If it cant be used or the remains of the plug still wont come out then the head will have to be removed and the spark plug removed from the inside. A machinist may be better suited to do this if you end up having to take your engine apart.


How do you take out a spark plug?

You take off the cap. Then pull out the spark plug. Put a new spark plug in. Then put the cap back on. Voila your done. Easy as pie!


What is the spark plug gap for a 1990Chevy 2500 with a 305?

Spark plug gap is where spark plug spark discharge is designed to take place. On a conventional spark plug, it is the area between the center and the ground electrode.


How do you change spark plug on craftsman snow blower?

Most snow blowers have the spark plug on top of the motor :to change a spark plug you get a spark plug wrench (take wire cap off the plug) put wrench on spark plug then turn counter clock wise to take it out. To put a new one back in reverse the proses


How do you change spark plugs in a z24 1998?

you must take the top module off the engine and then remove the rubber plugs that are on top of the spark plug, then use the spark plug sockets to get them out you must take the top module off the engine and then remove the rubber plugs that are on top of the spark plug, then use the spark plug sockets to get them out you must take the top module off the engine and then remove the rubber plugs that are on top of the spark plug, then use the spark plug sockets to get them out


What size spark plug socket do you need to take off plug on Honda 400EX?

You need an 18 mm spark plug socket.


How do you change the spark plug on a 2002 Kia Sedona?

You spend 340.00 paying the dealer to take half the engine apart so that there is access to the spark plugs. Other than the access problem there is nothing different about changing Kia Spark plugs.


How do i take off the spark plug for 660 raptor?

The best way is to use the spark plug socket out of the factory tool kit. If you do not have that use a normal 5/8" socket to loosen the spark plug. Use the spark plug wire to snap back on after the plug is loose and pull it out. The spark plug is at the very top of the engine, the spark plug wire is a real good indicator of its location.


How do you know if spark plugs and wires are bad?

Take the spark plug out, push back into it's pocket, set the spark plug on a grounded piece of metal, have someone crank the engine while the spark plug is grounded (but don't hold onto the spark plug, common sense right?) if a spark appears between the little arm the spark plug works, if it doesn't spark, replace with a new plug, and if the new plug doesn't start you have a faulty wire.


How do you change spark plug on snapper sx5200 snapper snow blower?

Take off the gas cap. Take off the big plastic cover with a socket and wrench.Then put the gas cap back on. Then pull of the spark plug boot. Then take off the spark plug with a spark plug socket and wrench. It should be 13/16" socket with 3/8" drive wrench. I Think the spark plug gap is 0.025 but you would have to look at a manual.


How do you check spark plug in lawn mower?

You pull the ruber boot off the top of the spark plug , take the plug out, put boot back on the plug, touch steel part of the plug to steel on motor,pull motor over while watching the gap on the plug if you see spark it should be ok if no spark do the same with a spark plug you know is good to make sure it is the plug. Hope this helps