0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How can you tell you have a bad coil on a 1968 Mustang?
Test it Primary resistance 1.40 to 1.54 ohms secondary resistance 7600-8800 ohms primary circuit resistor 1.30 to 1.40 ohms
How do you test an outboard motor coil?
Test your two primary points with ohms should read zero - where your spark plug wire goes in is your secondary - test it with one primary point should read resistance then test other primary point with secondary should read the same - coil is good - if two primary are not zero bad coil - if second with primary read zero coil is bad.
How do you test fire an ignition coil?
You test an ignition coil by checking the resistance with an ohm meter. The resistance values should be something like, Primary winding .3 to 1 ohms, Secondary winding 8,000 to 11,500 ohms.
How do you test the coil pack?
If you have an Ohm meter you will want to measure the resistance (ohms) of the Primary and Secondary sides of the coil pack and compare your readings to the Specifications for the vehicle.
What is resistance between primary and secondary winding of transformer?
The primary and secondary windings of a mutual transformer are electrically isolated, and should have 'infinite' resistance between them when measured appropriately (which depends on voltage ratings of the windings).
What is the distinguishing test between primay secondary and tertiary amine?
HINSBERG TEST IS THE DISTINGUISH TEST BETWEEN PRIMARY SECONDARY TERTIARY AMINE
What does chromic acid test and lucas test indicate?
if it is a primary, secondary or tertiary alcohol
What is the resistance of the secondary of a 24 volt transformer?
For the 120/24V transformer, the primary side is around 50ohm, the secondary side is 2~
What happens when secondary of the transformer is open?
The secondary winding leakage inductance limits the current during a short. It seems that the current through the primary is limited by winding resistance and leakage resistance when the secondary is shorted.
What is the ratio of primary to secondary turns of a transformer if internal resistance is 12.8 ohms and load resistance is 8 ohms?
600 by 208
How do you set up a transformer efficiency test?
You'll need a clean, stable primary side voltage source. You'll measure and monitor it throughout the test. You will need to measure primary current, too. You'll need a stable secondary resistance of known value, and you'll have to monitor voltage across it throughout the test. If you want to measure current, you can use an "unknown" resistance - as long as it is stable. You have a choice, and you can make your calculations based on either one. Your equipment will have to be "accurate" at least to the degree of accuracy you wish in your results. Hook up your resistance to the secondary, hook your equipment up to the various places you'll need it to make your measurements, plug in the primary and flip the switch. Observe and record. Your data will allow you to make calculations. Primary voltage times primary current equals primary power (power into the primary). Secondary voltage times secondary current will equal secondary power (power out of the secondary). There wil be a bit more power "put into" the primary than is "taken out of" the secondary because of losses within the transformer. (These will be resistive losses in the wire as well as inductive losses in the core - eddy currents.) And that is what efficiency speaks to. Transformer efficiency can be calculated using the following formula: Efficiencytransformer in % = 100 x (Powersecondary / Powerprimary) If you opt to use secondary voltage and the resistance of the resistive load to make your calculations for the secondary side power, it will be found by using this formula: Powersecondary = (Voltagesecondary)2 / Resistanceload Either path should lead to the same destination. And just so you know, if you use secondary current and the resistance of the load to make the calculation, that is done using this formula: Powersecondary = (Currentsecondary)2 x Resistanceload All roads lead to Rome.
What is DCR in transformers?
It is dc resistance, use to measure the rated current at primary and secondary side
