answersLogoWhite
Chevy Camaro RS
Lawn Mowers and Garden Tools
DIY Projects

How do you tighten or loosen a deck belt?

545556

Top Answer
User Avatar
Wiki User
Answered 2006-09-23 03:56:44

If refering to a riding mower deck belt tention is usually controlled by a spring attached to a floating pully or wheel. All depends on which one of the many mowers made you have

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Your Answer

Related Questions


Loosen bolt in tension pulley, then loosen tension bolt. Replace belt. Tighten tension bolt. Last, tighten bolt through pulley.


You can't, the belt is called a serpentene belt, you have to replace the belt.


You loosen (1/2 turn) the 15mm nut that locks the idler pulley. Then from under neath you turn the 13mm bolt that will tighten and loosen the belt. Be sure to tighten the lock nut when done.


Loosen the bolts on the alternator or P/S pump, whichever applies, and slide it back enough to loosen the belt. Look and you will see that it can be moved in order to loosen or tighten the belt. Deflection at center point of the belt is approximately 1/2 inch.Loosen the bolts on the alternator or P/S pump, whichever applies, and slide it back enough to loosen the belt. Look and you will see that it can be moved in order to loosen or tighten the belt. Deflection at center point of the belt is approximately 1/2 inch.


Make sure the lawn tractor has the parking brake engaged. Pull the spark plug wire to prevent it from accidentally starting. Unscrew the engine drive belt keeper rod and slide it out of the hole in the frame. Slide the engine drive belt off the pulley. Pull the tie pins out of the support rods and slide the rods out of the cutting deck. Loosen the bolts on the deck belt and pull the belt until it is taut. Tighten the bolts and replace the deck, then replace the other parts in reverse order.


The power steering belt has an adjustment pulley. To tighten the belt on a 1994 Acura Vigor loosen the adjustment pulley and pull it up higher than tighten it.


the only belt with a tensioner is the timing belt, to tighten the alt belt loosen the adjustment bolt then tap the alt back then retighten the bolt


the Serpentine Belt on the 91 Lebaron is on Tension Pulley, you dont tighten it. But if it is loose and you need to tighten it you just go and buy a new belt and put that on.


CHANGING ALTENATOR BELT: 1. loosen compressor bolts push towards engine to remove compressor belt 2. loosen power steering bolts and push pump towards engine to get slack to remove belt. 3. loosen altenator bolts pus it towards motor to get slack and remove belt. 4. put new belt on push altenator away from motor to tighten slack in belt and tighten bolts 5. push power steering pump away from motor to tighten belt and tighten bolts 6. push compressor away from motor to tighten belt and tighten bolts. REMOVE FAN BELT: Do steps 1,2,5 and 6 REMOVE COMPRESSOR BELT: Do steps 1and 6


Loosen alternator remove old belt. Reroute new belt, tighten alternator.


What kind of car? On an older car you just loosen the alternator and pull it until the belt is tight and then tighten the bolts back. On newer cars, there is a tensioner that pulls the slack out of the belt.


my belt keeps coming off my l130a 48" deck. all the pulleys are good, is there a way to tighten the belt?


To loosen the tension on a serpentine belt on a 2005 Grand Caravan 3.8L, turn the nut of the belt tension pulley to loosen it. Adjust the belt, then tighten the tension pulley by turning the nut in the opposite direction.


On a Mazda MX-3 (1994) you need to tighten the adjustment bolt that is close to the fire wall. Tightening the bolt loosen the belt - loosening the bolt tightens the belt


all u have to do is use a tire tool gently and push inward and it will loosen,pull the belt off, let go slowly when you install the belt and it will tighten by itself


remove skid plat ,then find ac belt tensioner,loosen lock bolt in center,then tighten long bolt until belt has right tension onit ,then tighten lock nut.


There is an idler pully next to the PTO clutch. Loosen the nut and slide the pully to loosen or tighten the belt. Hope this helps



The Troy-Bilt ride-on mower deck belt it tightened using adjusters on the pulleys that secure the belt. There should be a diagram demonstrating the location of these adjuster on the deck under the left foot pedal.


On a 4 cyl. you loosen the bolt that holds the adjuster to the alternator and then loosen the adjusting screw. You may need to hold pressure on the alternator to help it move or also loosen the bottom mount bolt of the alternator to the engine to allow the alternator to move easily. On a v6 you loosen the center nut on the adjuster pulley and then loosen the adjuster screw. Remove the old belt and install the new one. adjust the pulley to tighten the belt and tighten the pulley or tensioner. Belt is now installed.


take the pump off to loosen the belt first then put on belt and tighten pump and check tension in belt.


Loosen the central nut of the belt tension pulley. Loosen the tightening bolt. Remove the belt, install a new one. Set proper tension. Tighten the central nut.


To tighten the alternator best on a 240sx, loosen the bolt on the alternator on the drivers side. Pull on the alternator away from the engine to adjust the belt. When it has no more than a quarter inch of give, tighten the bolt to finish.


loosen the pulley, side the belt off, slide the new one on, tighten the pulley


loosen the nut on the idler pulley. There is a bolt at 10:00 o'clock from the pulley. Loosen this bolt until you can put the belt on then tighten the bolt till the belt is tight then tighten the nut on the idler pulley. Recheck the belt tension after a day or so..



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.