0
What else can I help you with?
1993 Plymouth sundance duster wont start you have already gotten a new starter and a starter relay and a ignition time delay relay what now?
I replaced the battery in my 1993 sundance noe the starter will not ingage
How do you set the clock on a 1993 Plymouth sundance?
To set the clock on a 1993 Plymouth Sundance, first, ensure the ignition is in the "Run" position. Locate the clock setting buttons on the dashboard; typically, there are two buttons labeled "HR" (hour) and "MIN" (minute). Press the "HR" button to set the hour and the "MIN" button to set the minutes until the correct time is displayed. Once set, the clock will retain the time even when the ignition is off.
What causes a Transmission leak on a Plymouth sundance?
A transmission leak on a Plymouth Sundance can be caused by several factors, including worn or damaged seals and gaskets, which can deteriorate over time due to heat and age. Additionally, loose or damaged transmission pan bolts can lead to fluid escaping from the transmission pan. Other potential causes include a cracked transmission case or a faulty cooler line. Regular maintenance and inspections can help identify and address these issues before they lead to significant leaks.
The grey and green wires going into the coil of a 1994 Plymouth sundance 4cyl which is positive which is ground?
In a 1994 Plymouth Sundance 4-cylinder, the grey wire typically serves as the positive wire, while the green wire is usually the ground. However, it's crucial to verify this with a service manual or wiring diagram specific to your vehicle, as wire colors can sometimes vary or change over time. Always ensure the ignition is off and take proper safety precautions when working with electrical components.
Installing distributor Chevy S-10?
restabbing distributor and setting time I'm replacing 4 cylinder motor in a 87 Chevy s10 how do I install distributor and get the truck in time
How do you time a 1990 Ford Tempo?
To time a 1990 Ford Tempo, first ensure the engine is at top dead center (TDC) on the compression stroke for cylinder number one by aligning the timing mark on the crankshaft pulley with the timing pointer. Next, check the position of the distributor rotor; it should be pointing towards the number one spark plug wire on the cap. If adjustments are needed, loosen the distributor hold-down bolt and rotate the distributor slightly until the timing light indicates the correct timing specification, which is generally around 10-12 degrees BTDC for this model. Finally, tighten the distributor bolt and recheck the timing to ensure it remains accurate.
What are the release dates for Sundance Directors Lab - 2009 First-Time Filmmakers 1-2?
Sundance Directors Lab - 2009 First-Time Filmmakers 1-2 was released on: USA: 1 August 2009
1990 acura integra put used Japanese motor in car replaced distributor with new rebuit motor starts and runs rough like out of time moving distributor doesn't make any difference?
verify that the engine is timed properly if that's ok check your compression and vacuum
What are the release dates for At This Time - 2002?
At This Time - 2002 was released on: USA: January 2002 (Sundance Film Festival)
Plymouth was founded in what year?
Plymouth was founded in the year 1620.
How do you time a 89 Plymouth horizon 2.2 liter?
To time a 1989 Plymouth Horizon with a 2.2-liter engine, start by warming up the engine to operating temperature. Next, locate the timing mark on the crankshaft pulley and the timing indicator on the engine block. Use a timing light connected to the number one cylinder spark plug wire and aim it at the timing marks; adjust the distributor until the timing mark aligns with the specified timing degree (usually found in the service manual). Finally, tighten the distributor bolt and recheck the timing to ensure it remains accurate.
How do you install a carburetor on a 1990 Chevrolet one ton with a 454 engine?
Since a 1990 truck has fuel injection, this will be a difficult and expensive task. Everything one the top of the engine will need to be replaced. If it has a throttle body instead of individual injectors the intake manifold, distributor and wiring will all have to be replaced. You will need to decide on what distributor will be used. My suggestion is to come up with another plan unless you have plenty of time and money.
