0
How do you turn idler screw that is seized up on 1981 Honda cb900c?
Wiki User
∙ 6y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you adjust the Idle control in a 1992 Honda Accord LX?
1992 Honda accord throttle body adjustinThe throtle body has a screw on it self where the intake clamps on to. it is located on top by all the vacuums you can turn the screw with a phillip screw driver.
Can you keep a Honda 185s from going over a certain speed?
yes. screw in theGovernor screw located on the throttle body
How do you adjust idle on Honda crf150?
twist the screw under the carb
How do you tighten a door handle on a 97 Honda Accord?
with a screw driver
How to install a short shifter in a Honda civic?
You either, simply unscrew it or there is a screw that you take out. More than likely a hex screw.
How do you install a front license plate bracket on a 2008 Honda civic?
Buy the bracket from Honda with the hardware. in the front grill you will see two screw holes. Just line it up with the bracket and screw it on.. That simple
Where is the idle screw on a 1990 Honda accord LX?
it should be on the throttle body
Where is the carb drain screw on a cb250 Honda?
on the left(shifter side) of the carb, on the float bowl. small standard screw (flat head)
How do you adjust a Honda wave 125cc carburetor?
The carburetor on a 125cc Honda Wave is adjusted by turning the idle mixture screw and idle speed screw along the front. Both are turned until the desired rpm and performance are achieved.
How to change the AC belt on a 1997 and 2000 Dodge Caravan?
Answer 1: 4 cylinder The A/C belt and the Alternator belt are the same on a 97 Caravan. Just losen the alternator bolt and it should be able to come of easy Answer 2: My 2000 Dodge Caravan 3.0 has two belts; one serpentine for the alternator and steering pump and a typical v-belt for the a/c. The serpentine is the wider belt of course and it snakes around the alternator pulley, a spring loaded tension idler, a fixed idler, a crankshaft pulley and a power steering pump. The tension idler is located nearest to the alternator and should appear as a tension idler on the serpentine belt path decal in the engine compartment or other belt diagrams that can be had on line or in a repair manual . The second idler is fixed and cannot be adjusted. The tension idler can be pulled down in an arc toward the front of the car with a 15mm wrench on the idler shaft bolt by applying pressure as if you were tightening the idler's shaft bolt until the idler's spring tension is overcome and idler will move in a forward arc thereby reducing the pressure on the serpentine belt so that the belt can be removed and/or installed. The tension idler does not require the loosening of any locking bolt as is the case with the a/c idler in the following paragraph. It might be easier to use an extension handle on the wrench in order to move the tension idler. It might also be easier to have a second person to move the tension idler,but in any case, make sure the socket or box wrench that you will be using is securely attached to the bolt. DO NOT USE A PRY BAR AS IT CAN EASILY SLIP! Turning the idler shaft bolt counterclockwise will simply be removing the idler. When the idler shaft bolt is released and is applying tension to the serpentine belt, ascertain that the belt has fit properly on each of the grooved pulleys. The a/c belt is a V-belt that connects the crankshaft and a/c compressor pulleys and the V-belt's tension is maintained by a manually adjustable idler pulley. Unlike the serpentine belt the V-belt doesn't have a spring loaded tension idler. The idler pulley creates belt tension by the turning of an adjustment screw which moves an idler pulley shaft bracket away from the tangential line of the a/c V-belt . Before the bracket will move in response of the turning of the adjustment screw however, you must loosen the idler pulley shaft screw to allow the bracket to slide. Screw the adjustment bolt counterclockwise to allow the idler pulley to free all tension and then some to facilitate the V-belt removal and/or installation. Once tension is removed from the belts, they can be removed. To get the serpentine belt off, the V-belt has to be removed, unless you are Houdini. The greatest physical exertion should be the movement of the tension idler and with an extension, a child could make the movement. To install the serpentine belt simply place it properly on the pulleys and idlers and release the tension idler. To install the V-belt, reverse the above V-belt removal steps and tighten the idler pulley bracket adjustment bolt until the belt is tight but do not over tighten the belt and DON'T FORGET TO TIGHTEN THE IDLER PULLEY SHAFT SCREW when you are satisfied with the tension! Check the belt area for tools and for improper conditions before starting the engine. Viel Glück Good luck. Answer 3: If you have a 3.3 or 3.8 liter you need to rotate the belt tensioner, which is below the alternator, with a 15mm wrench. You can now slide belt off.
How do you stop a 91 f150 from idling at 2500 rpm when the idler screw has been adjusted the intake cleaned and the throttle cable replaced?
Possibly fix the vaccuum leak !!
How do you put a oil drain plug back on a 1991 Honda Accord?
Screw it in clockwise.
