0
The switch will be below and to the left of the steering column.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
What type of headlights are in the kenworth T660?
You have a choice of halogen (H4, IIRC) or you can get HIDs.
How do you remove a door panel from a Kenworth T660?
Roll the glass down because the glass comes out with the panel.
In 18 wheels of steel haulin' how do you change trucks?
because i want a change a truck and i want t660 kenworth
What is the freon capacity of 1999 kenworth t600 with a sleeper?
It's 3 lbs, 12 ounces for the T660, and that's what it should be for the T600, as well.
What was the original sticker price of the 2008 Peterbilt semi truck model T600?
Peterbilt never made the T600. The T600 was built by Kenworth, and it ended production in 2007, at which point it was replaced in production by the T660.
Where do you put fuses in 2013 kenworth t660?
Left side of the truck, under the hood, against the firewall is where you'll find fuses primarily for the chassis nodes. Behind the clutch pedal is the primary fuse panel, both for the cab and sleeper.
What trucking company uses kenworth?
Plenty of them do. Swift Transportation has some T2000s, T600s, T660s, and W900Ls in their fleet. Navajo Expresses primarily uses the T660, T700, and T680. Stevens Transport uses the T2000, T660, T700, and I think the T680. Werner Enterprises runs some T660s. Western Distribution runs a lot of Kenworths. Just the ones I could think of off the top of my head.
Does heater duct have air filter for kenworth w900?
Open the hood, and it should be on the right side, encased in a hinged plastic cover. IIRC, the W900, T600, and T660 all use the same cabin air filter, which can be simply washed out and reused.
Why does the dash lights go out in a 2012 kenworth truck?
Most likely wiring harness issues... I'm guessing you have a T660? They're pretty bad for them, and tracing wiring is a nightmare in those things... not only do they have enough wire to wire up the Golden Gate Bridge in them, it goes in all sorts of unnecessary directions, and things which are traditionally relatively simple to wire up (e.g., power windows, lights, etc.) are sent through chassis nodes, then they go back to the ECM.. thank an engineer for thinking that one up.
Why your kenworth building pressure on coolant?
It would help to know which model Kenworth you have. The cooling system pressure shouldn't be more than 15 psi. On later years of the T600, the T660, the T680, some models of the T800, and some models of the W900, the radiator has two caps.. the first is the fill cap, and the second has a bung, and that is the pressure relief cap. If the pressure relief cap is faulty, it usually fails to hold pressure, although it can fail to release pressure, particularly if there is blockage in the bung itself. On Kenworth trucks which don't have this, the fill cap does double duty as the pressure relief cap. I would check those first.
How do I get to batteries on kenworth truck?
The model would help. On Kenworths, you typically have two options... either an externally-mounted battery box, which can be forward or behind the fuel tank on the driver side.... for example, on a W900, they're normally in front of the fuel tank on the driver's side, but when Swift bought a bunch to try enticing their drivers into lease-purchase circa 2004 - 2005, they had them moved behind the cab, in front of the drive axles.If you have a model with skirts (e.g., T2000, T700, T600, T660, T680, T880, etc., they're typically under the forward skirt on the driver's side. I don't remember what all fasteners you need to remove it on a T700 or T600 offhand, but for the T660, T700, T680, and T880, you need a ratchet and 17mm socket. Once you've undone those six fasteners, it pulls right off, and your battery box is there. On the T660, there's a plastic cover held in place by a rubber strap which will have to be removed.
Where is a fan filtter located on a Kenworth W900 heat is working but not blowing out hard enough?
Your HVAC filter should be located under the hood, on the right side of the vehicle, and against the firewall. I believe the W900s all use the same cab filter as the T600 and T660, so it'll be encased in a plastic cover which is hinged at the top and held in at the bottom with a rubber strap. There's no need to replace it if it isn't damaged - it can simply be washed out and reused.
