answersLogoWhite
Ford Ranger
Check Engine Light
Ford Ranger XLT

How do you turn off the check engine light on a 2000 Ford Ranger?

456

Top Answer
User Avatar
Wiki User
Answered 2008-04-16 11:47:57

A check engine light means you have a possible problem with the emission system , you should get the Ranger scanned for trouble codes to diagnose and repair the problem . Once the problem has been repaired the check engine light can be reset.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Your Answer

Related Questions



You can not disconnect the check engine light.


A flashing check engine light is an indication of a severe engine misfire.


Auto Zone will check your engine light for free... Write down the codes and go from there.


The check engine light is a " picture " of an engine , just to the left of the engine temperature gauge


According to the 2000 Ford Explorer Owner Guide : No , a separate fuse for the check engine light is not listed


Check the oxygen detector.


a 2000 dodge ram 1500 the check engine light is on and the code says torque converter and clutch and overdrive solenoid. what do you think that the problem is?


A flashing check engine light normally means you have a misfire.


a check engine light means something is wrong in the system. Take the vehicle to a parts store I use advance auto and they will tell you the code numbers there may be more than one problem. This will tell you what probems you have.


There are pages and pages of things that can cause a check engine light. You need to have it checked with a scantool. Then the code can be diagnosed and repaired.


You would really need to have your Ranger scanned for any trouble codes to diagnose and then repair the malfunction with your emission control system . There are just too many possibilities


There are pages and pages of things that can turn the check engine light on. You need to have it checked for codes to know what the cause might be.


Disconnect battery and leave for about 10 min. Then reconnect. The check engine light went away on mine.


A person can reset the check engine light by using an OBD scanner to clear the codes. This is after the problem is fixed.


There is no individual fuse. The ECM has 2 or 3 fuses, and it controls the check engine light.There is no individual fuse. The ECM has 2 or 3 fuses, and it controls the check engine light.


The check engine light comes on when the computer detects a malfunction and sets a code.The check engine light comes on when the computer detects a malfunction and sets a code.


You hook up a scanner and check it for codes.


There are pages and pages of things that can cause a check engine light. You need to have it checked with a scantool. Then the code can be diagnosed and repaired.


yeah too much oil or low on oil will trigger the check engine light it happen to me on my 2000 altime gxe .


I don't know about the 2000 year model directly but the 1996 is similar I am sure. To reset the "check engine" light, find the EFI fuse (probably under the hood in the fusebox on the driver's side) and with the engine off, remove it for one minute minimum. Replace the fuse and the "check engine" light should be reset.


Bank 1 is the passenger side of a V6 engine in a 2000 Ford Ranger


You can disconnect the battery for a few minutes and that will clear the light. If there is a problem with the engine the check engine light will come back on. If it comes back on you will have to have the computer code read and fix the problem.


There are pages and pages of things that can cause a check engine light. You need to have it checked with a scantool. Then the code can be diagnosed and repaired.


I clear the check engine light with a Scangauge II. But most ODB-II devices can read and clear the code.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.