0
What else can I help you with?
Can a Laars Lite 2 heater for a chlorine pool be used if you convert to salt water?
Yes, a Laars Lite 2 heater can be used with a saltwater pool, but it's important to ensure that it is compatible with saltwater systems. Saltwater can be more corrosive than traditional chlorine, so you should check for any specific guidelines or recommendations from the manufacturer regarding saltwater use. Regular maintenance and monitoring of the heater's condition are also advisable to prevent potential corrosion issues.
Have a laars lite 2 pool heater and cannnot get pilot to even lite you hear gas bleeding but it will not lite?
Good chance its your hot surface ignighter that has broken. Check to make sure that there is 120 v or far more common 220v at fenwal Depending if heater is wired for 120v or 240v. If proper voltage is present ignighter is broken. by zoomy
Why would burner pilot light extinguish shortly after firing up on Laars Lite Model LLG Pool heater?
Have the thermocouple checked or spillage from down draft and make sure there is free air for proper combustion
Why won't your laars lite pool heater turn on The heat exchanger temperature sensing bulb and siphon loop assembly have all been replaced with no leaks.?
When was the last time the filter was cleaned? Have all the components in the heater system been checked for proper values? Does the heater sound as if it wants to fire up? Does it have a pilot light or electronic ignition? Have the orifices been checked for bugs or spiders? Ken
Can a heat exchanger be replaced on a laars lite 2 LD400P?
Yes, a heat exchanger can be replaced on a Laars Lite 2 LD400P. However, it is important to ensure that you obtain the correct replacement part and follow the manufacturer's guidelines for installation. If you're not experienced with boiler maintenance, it’s advisable to hire a qualified technician to perform the replacement to ensure safety and proper functioning.
Laars teledyan lite 2 model llg 125 - standing pilot and the pilot does not stay lit you have replaced the gas valve and the pilot burner assembly already?
If the pilot light on your Laars Teledyne Lite 2 model LLG 125 does not stay lit after replacing the gas valve and pilot burner assembly, check for proper gas supply and ensure there are no blockages in the gas line. It's also important to verify that the thermocouple is functioning correctly; it may need replacement if it fails to generate sufficient voltage. Additionally, inspect the venting system for any obstructions that could affect combustion and pilot operation. If the issue persists, consulting a qualified technician may be necessary for further diagnosis.
Would water heater lite if gas was turned off?
No.
What other problem besides the thermocouple would cause a heater not to stay lite?
The thermocouple only keeps the pilot light. Temp sensor,gas valve, high limit switch, safety switch,thermostat, would cause burner not to stay lite. Better to post MFG,model, problem. lenox,model #, ______________________________
Pilot lite on teledyne laars mini therm 2 wont stay lit?
Replacing the thermocouple that the pilot flame touches when it is lit will fix the problem 90% of the time. A thermocouple costs about ten dollars and allows the gas to the pilot and main tube to flow by generating millivolts from the heat of the pilot flame. The thermocouple is a copper wire attached by a small nut to the main gas valve near the pilot tube coming out of the gas valve.
What is wrong if your pilot light will not stay lite?
High winds, pilot generator. Is the heater located next to a wall? Is the heater door closed? Does the heater have a draft hood or what they call a stackless heater? Ken
Dash lights do not lite up?
my g6 heater and shifter console does not light up
Replaced the pilot generator on a Laars lite and it generates 670 to 700 millivolts however pilot won't stay lit when releaseing the valve Is it a bad gas valve Is it worth the money to replace?
Assuming you are getting that measurement at the valve would indicate a strong pilot generator and if the valve still will not open then I would pronounce the gas valve DOA. To replace the valve cost can vary from $350 to $650 depending on the Contractor due keep in mind that you've replaced the Pilot Generator and now a valve to finsh the job right install a new Pilot Body with the correct orifice and that will round out a reliable system. Good luck! Tim J&K Heating and Cooling Inc.
