Answer for USA, Canada and countries running a 60 Hz supply service.
Wiring of air compressor's pressure switch to a contactor.
Connect a 240 volt supply from the two pole breaker in the distribution panel to the top terminals L1 and L2 on the magnetic contactor.
Take a control wire from one of the line terminals L1 to one side of the contactor's coil.
Take another control wire from the second line terminal L2 and put it to one side of a N.C. contact on the overload block.
From the other side of the N.C. contact on the O/L block take a control wire to the N.C. terminal on the air compressor's pressure switch.
From the other side of the N.C. contact on the pressure switch's terminal connect the control wire to the other side of the contactor's coil.
This configuration will be using the same coil voltage on the contactor as that of the supply voltage.
From the overload block line terminals T1 and T2 connect a cable to the motor's terminal box and connect.
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Yes, there is a difference between single phase and three phase circuits.
working of single phase preventor
Single phase inherently requires less equipment (it's cheaper). Three phase motors are more efficient than single phase.
In single phase motors, there are two windings. 1)Main winding 2) starter (auxiliary) winding. As per the double revolving theory in 1 phase machines, motor can rotate if current in the starter winding have near to 90 deg. phase shift wrt main winding. Now current flowing through capacitor leads by 90 deg. Ideally. So this is how we can get two currents which are having phase shift wrt each other. And the machine can rotate.
Two phase is single phase for today's purposes. We generally do not call 240v single phase "two phase" anymore, although technically that's what it is. 240v two phase has power to both lines to the motor versus 120v single phase has one power line and a neutral. Fortunately most single phase motors today are dual voltage. So check your nameplate data of the motor for guidance. The use of proper motor protection will prevent any damage to motors if wrong voltages are inadvertantly applied.CommentA two-phase system is an archic system, in which two phase voltages are displaced from each other by 90 electrical degrees. Like three-phase, it had the advantage of producing a naturally-rotating magnetic field, so could drive induction motors without any need for a starting capacitor.
A starter is unnecessary because the stator produces a rotating magnetic field.
Shading coils provide a phase shift between the magnetic field of the rotor and stator, which is necessary to get the motor spinning.
Nah doesnt exist
It's depend on refrigerant.
One uses single phase AC current (120/240), the other uses 3 phase AC current (most households will not have 3 phase in their home) One uses a 3 phase motor the other a single phase motor. 3 phase is usually used in industrial applications while single phase is used in home or small business apps.
C = common S= start R= run
It provides the phase shift necessary to have a rotating magnetic field for the rotor to spin. Answer #2: single phase induction motor can create pulsating magnetic field. due to single phase forward and backward torque created also they cancel led each other.so we want to extra force to rotate rotor either forward or reverse direction or we can give rotating magnetic field by using capacitor(phase split)
For 1 hp motor, a single phase starter is used. Because a single phase starter gives economy consumption,easy trouble shooting and easy installation when compared to three phase starters and supply....
capacitive start motors start by themselves however a normal single phase induction motor requires a starter motor to 'kick-start' the motor into action.
yes
No, three phase motor overloads just monitor the motor's lines for an overload. Once detected the circuit holding the magnetic starter in will drop out and take the motor off line.
The changing magnetic flux in the iron core of the transformer induces a voltage in the windings.