The inductive ballast is made up of a coiled wire. The coil creates a magnetic field inside when a current is applied. It stores the energy of the current in the magnetic field it creates. This way it controls the output current that continues on to the light. The store of energy also helps in the starting of the light when it is off, by sending an extra volt of electricity when the current first starts into the coil.
I actually have a 400w hps ballast and I can also use my 400w metal halide bulb in it with no problem. So what your saying is they do, but they dont? the answer is, they dont. You can get universal bulbs hps to plug into a mh ballast they have a miniturized igniter inside the bulb. As I understand it, a 400W metal halide bulb can be used with a 400W hps ballast, but not the converse. A MH bulb has the igniter in the bulb, and the HPS has it in the ballast--which pretty much goes along with your comment above. Apparently the double presence of the igniter in the HPS setup is OK.you can run metal halide in same wattage's but not hps in metal halide systems.you can run such as (same wattage's)250 watt metal halide-400 watt halide ect in hps systems but not hps bulbs in halide systems. they make conversion bulbs to run halide in hps as well and vice versa.
Yes, a ballast is required for HPS (high-pressure sodium) lights. The ballast helps regulate the electrical current and provides the initial high voltage needed to start the lamp. Without a ballast, the HPS light would not function properly.
A higher wattage HPS bulb may work with a ballast that is rated for a lower wattage bulb , but may appear to be dim and will not produce the rated light output. It is best to match ballast and bulb accordingly.
The formula you are looking for is W = Amps x Volts. Find the amperage and voltage that is on the nameplate of the HPS fixture's ballast.
You need the appropriate ballast for either of these bulbs to make them light.
No!
No, the ballast has to be matched to the lamp. 250 watt ballast, 250 watt lamp. Also be sure to match the lamp type to the proper ballast even though the wattage is the same. HPS ballast to HPS lamp, Metal halide ballast to metal halide lamp and mercury vapour lamp to mercury vapour ballast.
yes
100 Volts
Yes the ballast and starter are the same you can run halide in hps, but not hps in halide.
I actually have a 400w hps ballast and I can also use my 400w metal halide bulb in it with no problem. So what your saying is they do, but they dont? the answer is, they dont. You can get universal bulbs hps to plug into a mh ballast they have a miniturized igniter inside the bulb. As I understand it, a 400W metal halide bulb can be used with a 400W hps ballast, but not the converse. A MH bulb has the igniter in the bulb, and the HPS has it in the ballast--which pretty much goes along with your comment above. Apparently the double presence of the igniter in the HPS setup is OK.you can run metal halide in same wattage's but not hps in metal halide systems.you can run such as (same wattage's)250 watt metal halide-400 watt halide ect in hps systems but not hps bulbs in halide systems. they make conversion bulbs to run halide in hps as well and vice versa.
Yes, a ballast is required for HPS (high-pressure sodium) lights. The ballast helps regulate the electrical current and provides the initial high voltage needed to start the lamp. Without a ballast, the HPS light would not function properly.
The MH ballast will not have the ignitor required to power up the HPS bulb. I have 1000w ballast that can be switched between HPS and MH with a singe switch just by disabling the ignitor for the MH. I would look into conversion bulbs, or else check out this site for $20 150w HPS ballast with bulb. http://www.e-conolight.com/Product/EProductDetail.asp?ProductFamilyID=7&FGNumber=E-MT6H151G If it doesnt appear, sellect vapor tights, then the 150hps.
A higher wattage HPS bulb may work with a ballast that is rated for a lower wattage bulb , but may appear to be dim and will not produce the rated light output. It is best to match ballast and bulb accordingly.
The formula you are looking for is W = Amps x Volts. Find the amperage and voltage that is on the nameplate of the HPS fixture's ballast.
If the ballast of the HPS fixture has a 120 volt tap then, yes it can be plugged into a 120 volt receptacle.
I would wire them together in a parellel circut. all the lights together, white to white black to black then put your ballast to em. it works like that with my 400 watt mh/hps ballast and 2 250 watt hps bulbs. run 2 hps bulbs with 2 mh bulbs if you can, you get better results.