0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the main difference of Bunsen burner to alcohol lamp?
Alcohol lamp- is used as a source of heat and light . Bunsen burner- source of heat when non-luminous flame is needed for experimental work..
Bunsen burner parts?
A normal Bunsen burner has a chimney which contains gas, a collar to adjust the air hole, a air hole that will leak gas, a gas tap that provides gas to the burner and the rubber tubing leads gas to the burner.
What would you do without Bunsen burner?
If you need to heat something: use an electric hot plate, water bath, or incubator. If you need a naked flame: light a match, lighter, or candle. If you need to work glassware: a butane lighter with a concentrated flame may work for small glassware (e.g. pipettes), for larger pieces you may need to go to a glassworking shop or find a Bunsen burner or forge.
What does the work in an electric circuit?
The load that is connected in a circuit is what does the work in the circuit.
How do you get different colors of fireworks?
Do make a color flame with a Bunsen burner you have to twist the collar part around there is 3 settings: A full closed one with no hole makes a colored flame, a half makes a flame just enough to see and the last one, which is completely open will make the hole see through but the flame.
How does a cooker flame safety device work?
It stops the gas supply to the burner when there is no flame sensed by the thermocouple inside the burner.
What is the similarities of alcohol lamp and Bunsen burner?
Both needs flame to work
What is the work of diaod in computer ups?
it depends on where it is located on the ups circuit. typically you should find rectifying diodes, clamps, voltage reference, and switching diodes in a ups system
What is the main difference of Bunsen burner to alcohol lamp?
Alcohol lamp- is used as a source of heat and light . Bunsen burner- source of heat when non-luminous flame is needed for experimental work..
Bunsen burner parts?
A normal Bunsen burner has a chimney which contains gas, a collar to adjust the air hole, a air hole that will leak gas, a gas tap that provides gas to the burner and the rubber tubing leads gas to the burner.
What is your responsibility for rectifying risks in your workplace?
depends on what type of work is perform there
How does a flame sensor work in home furnaces by using a metal rod in the flame?
Its not a flamesensor its a pilot generater it generates a small amound of electricity to open the main valve that way if your pilot light goes out it wont let gas escape and couse a potentian explosion The above answer is not accurate unless you have a standing pilot model furnace. Then the "flame sensor is called a thermocouple, much different than the flame sensors used in Direct Spark Ignition, hot-surface and intermitant ignition furnaces. The flame sensor uses the flame of the main burner to prove flame at the circuit board by measuring conductivity to ground through the flame.
What safety rules apply when using Bunsen burners in the lab?
- don't work with flammable, explosive, very toxic or radioactive chemicals - work in a fume hood - use protective glasses - survey permanently the flame of the burner - do not let the flame open when you go home
What would you do without Bunsen burner?
If you need to heat something: use an electric hot plate, water bath, or incubator. If you need a naked flame: light a match, lighter, or candle. If you need to work glassware: a butane lighter with a concentrated flame may work for small glassware (e.g. pipettes), for larger pieces you may need to go to a glassworking shop or find a Bunsen burner or forge.
What is a lab burner?
A laboratory burner, enables glassware (safe to be heated) containing chemicals or any liquid or solid to come to a boil or a certain temperature.
How does an oil burner work?
Oil burner magic!!
How does a inshot burner work?
Gas fired appliances, such as residential and light commercial heating furnaces, often use a particular type of gas burner commonly referred to as an in-shot burner. In this type of burner, fuel gas under pressure passes through a central port disposed at the inlet of a burner venturi. Atmospheric air is drawn into the burner and mixes with the fuel gas as it passes through the burner. In some constructions, a burner head insert, also referred to as a flame retention insert, made of compressed sintered or powdered metal is mounted in the outlet end of the burner tube. In operation, as gas is injected into the inlet end of the burner, it entrains air into the burner. This primary air/gas mix flows through the burner to the flame retention insert. The primary air/gas mix passes through outlet openings defined by the insert and burns as it exits the insert forming a flame projecting downstream from the burner head insert. Secondary air flows around the outside of the venturi tube and is entrained in the burning mixture downstream of the insert in order to provide additional air to complete the combustion process. Read more in the related link
