Asked in Uncategorized
How does plstic softnees?
We need you to answer this question!
If you know the answer to this question, please register to join our limited beta program and start the conversation right now!
Asked in Michael Jackson
What happens when Michael Jackson gets plstic surgery?
Asked in Food & Cooking
Will you be okay if you eat melted plstic in your food bye accident?
Asked in Chemistry
A piece of plstic is stretched until it breaks physical changeor chemical change?
How many doctors in LA perform plstic surgery?
Asked in Airsoft Guns and Accessories
Can the plstic on a airsoft gun break if it is shot?
1994 Chevy S10 Front left turn signal dim has bad ground were is it located?
Asked in Renault Clio II, Renault Clio
Where is the pollen filter on an 1999 Renault clio?
How do you change the license plate light bulbs on a 2002 Chevy Trailblazer?
There is a small plstic cover over the bulb housing with two screws. Remove both screws, pop off the cover and expose the burned out bulb. You will just need to pull on the bulb. I suggest you pull carefully so as not to break it, but it is just a slip in so keep pulling until it releases. By the way the replacement bulb is a size 168.
How do you reset a Silencer car alarm on your 2002 kia Rio?
there should be a light (red) attached to your dashboard. you should have a button, would have been in a plstic case with your remotes when you bought the car. button in the off position place it in the hole on the back of the light. turn the key for your car to the on position and push the button. the horn should then shut off, and the light on your dash turn on solid. you should now be able to start your vehicle good luck!!!!! if you are still having problems check out magnadyne.com to find a local dealer
How do you replace the headlight bulb located on a 2002 Chevrolet Avalanche?
the light above the headlamp snaps out after releasing a small plstic tab. This then will let you see two small diameter rods on top of the lamp assy. lift these up and the headlamp assy will come out inyour hands. Then the bulb replacement is obvious. P.S. use a paper towell or something to prevent the oil from your hands contaminating the new bulb. Any oil transfer will cause a hot spot and the replacement bulb will not last long.
Asked in Academic Writing, Paragraph Development
Example of expository writing?
This is an example of an expository paragraph In 1997, 175,000 volunteers picked up three million pounds of garbage along the coasts of the United States. As a result, both people and sea animals can enjoy cleaner and safer environments. Glass bottles, lumber, and syringes are less of a threat to barefooted beachgoers. Fewer sebirds, fish, and crabs will die entangled in plstic can holders, fishing nets, and fishing line.People put trash in the oceans, but by volunteering their time to help clean up after themselves, people are also the solution to the problem.
How do you replace the light in a 2002 Honda clock?
I have a 2000 acord with the rectangular clock in the center of the panel. I just took a wide flate blade like a butter knife and inserted it in the gap at the bottom of the clock and worked it out. I first tried the top but is has to be the bottom. The light has a very small plstic base that just quarter turns out. I now have to see if Honda has a replacement. Since you don't know what model you have, I'll offer this: Remove the screw around the dash instrument panel pull the instrument panel out carefully, remove the top 3 connectors replace the bulbs in back as needed. reassemble. Keep in mind this applies to some hondas, maybe not you model. Especially if the clock is not in your IP.
How do you remove the driver's side door panel on a 2001 Chrysler Town and Country?
I did this myself a while ago. You will need a special tool, that they sell at NAPA. Just explain whatyou need it for. They should know what you're talking about. Unscrew the screw that is in the door handle and the one that is under the inside panel in the front. It's kind of hard to see but it's toward the front of the door. Be gentle with the tool once you got these screws out, otherwise it is really possible that you'll brake of the plstic thing that is holding the inside of the door in place. Once youhave popped all the plastic things out continue to be careful, bend the inside gently outwards as you look for the mounting that is the connection between the panel and the door. dismount. Lift carefully and unplug all the wires you see
How do you change a starter on a 1996 Chevy Lumina mini van?
Well, .. for a 1994 Lumina APV - here's what I did: I replaced the starter in my 1994 Lumina APV (3.8 L V6) after about 120,000 miles. Symptom was that the starter would turn over very slowly when the engine was hot. Nice gentleman @ Autozone told me that the coils tend to deteriorate and heat conducted from the engine causes the starter to heat up and then draw high current when hot. Cold starts were fine - hot starts caused the starter to turn very slowly (like the battery was drained). He tested the starter and it tripped the breaker on the tester two (2) times. Got a remanufactured one for ~$65. Here's what I did. 1) Disconnect cable from negative battery terminal 2) Raise vehicle front and suitably and safely support. 3) Remove cover from starter wiring (small right angle-like black plastic cover). 3) Loosen large wiring harness (underneath starter) so that it can be moved out of the way. 4) Remove outer nut and wires from solenoid. 5) Remove outer nut and wires wires from starter. 6) Remove two (2) screws retaining plastic flywheel cover and cover. You will need to do this - otherwise you will be unable to remove the front bolt holding the starter to the engine block. This cover is a small black plstic piece located where starter penertates the flywheel cover. 7) Remove (2) bolts retaining starter to the engine block. One is accessable towards the front of the starter/vehicile and the other (long one) is towards the rear of the vehicle - just behind the frame cross member. 8) Position starter so that if can be dropped down (flywheel gear part first). 9) Reverse the above instructions to install the new starter/solenoid. Palmboy (6/25/05)